Question is ⇒ As the number of cylinders in multi cylinder engines increases the power to weight ratio ........., Options are ⇒ (A) Remains the same, (B) Increases, (C) Becomes zero, (D) Decreases, (E) , Leave your comments or Download question paper.

Question is ⇒ As the number of cylinders in multi cylinder engines increases the power to weight ratio ........., Options are ⇒ (A) Remains the same, (B) Increases, (C) Becomes zero, (D) Decreases, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	As the number of cylinders in multi cylinder engines increases the power to weight ratio .........
A.	Remains the same [Wrong Answer]
B.	Increases [Correct Answer]
C.	Becomes zero [Wrong Answer]
D.	Decreases [Wrong Answer]
View Answer 12 -28 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The coil spring clutch may use from
Two to six springs
Three to nine springs
Four to eight springs
Ten to twelve springs

⇒ The axle bevel gears in the differential mesh with the
Differential pinion gears
Ring gear
Drive pinion
Main gear

⇒ The substance added to the oil which helps to keep the engine clean is called
Grease
Thickening agent
Soap
Detergent

⇒ The front end of the clutch shaft is supported in a pilot bearing in the
Throw out bearing
Friction disc
Crankshaft
Transmission

⇒ When we lift a 10 kg weight, 3 metre we would be doing
300 m kg of work
3 m kg of work
30 m kg of work

⇒ In the hydraulic brake system, movement of a piston in the master cylinder produces hydraulic pressure which causes movement of the
Wheel cylinder pistons
Brake pedal
Brake cam

⇒ For each crankshaft revolution, the cam shaft revolves
one half-turn
one turn
two turns
four turns

⇒ Of the four tyres on a car, the one that wears most is the
Right front tyre
Right rear tyre
Left front tyre
Left rear tyre

⇒ The sun gear in the planetary gear system meshes with the
Pinion cage
Ring gear
Clutch gear
Planet pinions

⇒ The fuel injected when pressure in the cylinder reaches the point ........... on the curve
1
2
3
4

⇒ In the engine there must be relative motion between the piston and the connecting rod
Atmospheric pressure, inertia and torsional vibration
Centrifugal force, inertia and combustion pressure
Inertia, engine speed and centrifugal force

⇒ In the power assisted type of brake the bellows applies force to the master cylinder piston
Through diaphragm linkage
Directly
Through mechanical linkage

⇒ When an automobile takes a tum to avoid the skidding and over turning
Each wheel will roll independently
Front two wheels will have a common centre during a turning
All the 4 wheels will roll on arcs having a common centre

⇒ In the vacuum suspended system, the brakes are applied when
Atmospheric pressure is applied to one side of the diaphragm
Vacuum is applied to both sides of diaphragm
Atmospheric pressure is applied to both sides of the diaphragm

⇒ In the diesel engine, the compression ratio is as high as
10:1
15:1
5:1

⇒ The distance between adjacent meshing teeth of mating gears is called
Clearance
Back lash
Flank

⇒ One advantage of using an exhaust valve as insert is that the ring
Withstands high exhaust gas temperature better
Is more easily machined
Wears in more quickly

⇒ Whirling of the propeller shafts is mainly due to
The transmission of torsional vibration of the crankshaft
The use of a sliding joint in the propeller shaft
The use of universal joints in the drive
Lack of balance and excessive length of propeller shaft

⇒ The most commonly used material for tyre tubes is
Butyl
Natural rubber
Butane

⇒ In general the design of the current regulator is such that its main actuating winding carries full
Generator voltage
Generator output
Field current
Battery voltage

⇒ In a vacuum suspended unit, when the brakes are on, the piston or diaphragm has on both sides of it
Atmospheric pressure
Vacuum
Hydraulic pressure

⇒ The distance between dual tyres of vehicles is to be correctly spaced to
Ensure proper distribution of load between dual wheels
Reduce over-steering effect
Reduce the slippage between tyre and road while taking a turn
Ensure effective braking

⇒ In the diaphragm clutch inward movement of the throw out bearing causes the diaphragm spring to
Dish inward
Expand
Contract

⇒ As the number of cylinders in multi cylinder engines increases the power to weight ratio .........
Remains the same
Increases
Becomes zero
Decreases

⇒ In the multiplier type of brake, the diaphragm acts directly on the hydraulic piston in the
Master cylinder
Wheel cylinder
Multiplier unit

⇒ The maximum pressure of air fuel mixture at the end of compression in petrol engines varies from
10-30 Kg/cm2 b. 30-100 Kg/cm2
6-10 Kg/cm2
100-1000 Kg/cm2

⇒ In the differential the ring gear is bolted to the
Differential housing
Differential case
Axle housing
Drive pinion

⇒ If the differential noise is present only when the car is rounding a curve the trouble would be due to
Heavy heel contact on gear teeth
Heavy toe contact on gear teeth
Binding in differential case

⇒ To correct heavy toe contact on ring gear teeth, move the
Ring gear towards pinion
Ring gear away from pinion
Drive pinion out and back lash

⇒ The fit of the piston to the cylinder is measured at the
Piston skirt
Piston head
Point of minimum diameter