Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | Application of Norton's theorm to a circuit yields |

A. | equivalent current source and impedance in series [Correct Answer] |

B. | equivalent current source and impedance in parallel [Wrong Answer] |

C. | equivalent impedance [Wrong Answer] |

D. | equivalent current source [Wrong Answer] |

View Answer
Explanation:-
Answer : ADiscuss it below :Sudarshan sen Said on 2021-11-14 23:02:06option B is correct Chittaranjan Said on 2017-08-20 00:15:40Correct answer is B Pradeep Said on 2017-06-23 10:40:45B is right answer. Md Said on 2016-11-16 07:42:31Option B is right not A !! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ For a voltage source

terminal voltage is equal to the source emf.

terminal voltage cannot exceed source emf.

terminal voltage is always lower than source emf.

terminal voltage is higher than the source emf.

⇒ Which of the following is non-linear circuit parameter?

Inductance

Condenser

Wire wound resistor

Transistor

⇒ If the number of branches in a network is 'B', the number of nodes is 'N' and the number of dependent loops is 'L' then the number of independent node equations will be

N + L - 1

B - 1

B - N

N - 1

⇒ In nodal analysis, if there are N nodes in the circuit, then how many equations will be written to solve the network?

N - 1.

N + 1.

N.

N - 2.

⇒ A capacitor is generally a

bilateral and active component

active, passive, linear and nonlinear component

linear and bilateral component

non-linear and active component

⇒ Kirchhoff's s law is applicable to

passive networks only

a.c. circuits only

d.c. circuits only

both ac. as well d.c. circuits

⇒ A closed path made by several branches of the network is known as

branch

loop

circuit

junction

⇒ "Any number of current sources in parallel may be replaced by a single current source whose current is the algebraic sum of individual source currents and source resistance is the parallel combination of individual source resistances".

The above statement is associated with

Thevenin's theorem

Millman's theorem

Maximum power transfer theorem

None of the above

⇒ Which of the following is the passive element?

Capacitance

Ideal current source

Ideal voltage source

All of the above

⇒ A connected network of N > 2 nodes has at most one branch directly connecting any pair of nodes. The graph of the network

must have at least N branches for one or more closed paths to exist?

can have an unlimited number of branches?

can only have at most N branches?

can have a minimum number of branches not decided by N?

⇒ In a series parallel circuit, any two resistances in the same current path must be in

series with each other

parallel with each other

series with the voltage source

parallel with the voltage source

⇒ Kirchhoff's current law states that

net current flow at the junction is positive

algebraic sum of the currents meeting at the junction is zero

no current can leave the junction without some current entering it.

total sum of currents meeting at the junction is zero

⇒ The lowest and the highest critical frequencies of an R-L driving point impedance are, respectively

a zero, a pole

a pole, a pole

a zero, a zero

a pole, a pole

⇒ In a balanced Wheatstone bridge, if the positions of detector and source are interchanged, the bridge will still remain balanced. This inference can be drawn from

reciprocity theorem.

duality theorem.

compensation theorem.

equivalence theorem.

⇒ Millman's theorem yields

equivalent resistance

equivalent impedance

equivalent voltage source

equivalent voltage or current source

⇒ "Maximum power output is obtained from a network when the load resistance is equal to the output resistance of the network as seen from the terminals of the load".

The above statement is associated with

Millman's theorem

Thevenin's theorem

Superposition theorem

Maximum power transfer theorem

⇒ A voltage source having an open-circuit voltage of 100 V and internal resistance of 50 ω is equivalent to a current source

2 A in parallel with 50 ω.

2 A with 50 ω in series

0.5 A in parallel with 50 ω

A in parallel with 100 ω

⇒ While calculating R

_{th}in Thevenin's theorem and Norton equivalent

all independent sources are made dead

only current sources are made dead

only voltage sources are made dead

all voltage and current sources are made dead

⇒ Which of the following is not a nonlinear element?

Gas diode

Heater coil

Tunnel diode

Electric arc

⇒ For a two-port symmetrical bilateral network, if A = 3 and B = 1 ω, the value of parameter C will be

4 s

6 s

8 s

16 s

⇒ An electric circuit with 10 branches and 7 nodes will have

3 loop equations.

4 loop equations

7 loop equations

10 loop equations.

⇒ Which of the following is an active element in a circuit?

Current source

Resistance.

Inductance.

Capacitance.

⇒ For a voltage source

terminal voltage is always lower than source e.m.f.

terminal voltage cannot be higher than source e.m.f.

the source e.m.f. and terminal voltage are equal

⇒ Kirchhof's voltage law applies to circuits with

non-linear elements only

linear elements only

linear, non-linear, active and passive elements

linear, non-linear, active, passive, time varying as wells as time-invariant elements

⇒ A network which contains one or more than one source of e.m.f. is known as

linear network

non-linear network

passive network

active network

⇒ A star circuit has element of resistance R/2. The equivalent delta elements will be

R/6

3/2R

2R

4R

⇒ Efficiency of power transfer when maximum transfer of power occurs is

100%

80%

75%

50%

⇒ The circuit has resistors, capacitors and semi-conductor diodes. The circuit will be known as

non-linear circuit

linear circuit

bilateral circuit

none of the above

⇒ Which of the following is a bilateral element?

Constant current source

Constant voltage source

Capacitance

None of the above

⇒ A constant current source supplies a current of 300 mA to a load of 1 kω. When the load is changed to 100 ω, the load current will be

3 A

300 mA

30 mA

100 mA