Question is ⇒ An imaginary line along which rivets are placed, is known as., Options are ⇒ (A) rivet line, (B) scrieve line, (C) gauge line, (D) all the above., (E) , Leave your comments or Download question paper.

Question is ⇒ An imaginary line along which rivets are placed, is known as., Options are ⇒ (A) rivet line, (B) scrieve line, (C) gauge line, (D) all the above., (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	An imaginary line along which rivets are placed, is known as.
A.	rivet line [Wrong Answer]
B.	scrieve line [Wrong Answer]
C.	gauge line [Wrong Answer]
D.	all the above. [Correct Answer]
View Answer 40 -17 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Tongue plates are provided in a steel girder at.
the upper flange
the lower flange
the lower end of the web
the upper and lower ends of the web.

⇒ The best arrangement to provide unified behavior in built up steel columns is by
lacing
battening
tie plates
perforated cover plates

⇒

Effective sectional area of a compression member is :

gross sectional area - area of rivet hole
gross sectional ares + area of rivet hole
gross sectional ares x area of rivet hole
gross sectional ares + area of rivet hole.

⇒ The moment-curvature relation at a plastic hinge is
linear
parabolic
constant moment for all curvatures
constant curvature for all moments

⇒ Bolts are most suitable to carry
shear
bending
axial tension
shear and bending

⇒ The actual thickness of butt weld as compared to the thickness of plate is usually
more
less
equal
none of the above

⇒ The deflection of a beam may be reduced by
Decreasing the depth of beam
Increasing the span
Providing greater end restraint
Any of the above

⇒ The percentage of carbon in structural steel is
0.20 to 0.27 %
0.70 to 0.80 %
1.20 to 1.27 %
1.70 to 1.80 %

⇒

Web crippling generally occurs at the point where.

bending moment is maximum
shearing force is minimum
concentrated loads act
deflection is maximum

⇒ With a percentage increase of carbon in steel, decreases its.
strength
hardness
brittleness
ductility.

⇒ The maximum permissible slenderness ratio of compression member carrying dead and superimposed load, is.
180
200
250
300

⇒ In bridge floors the longitudinal beams supported by floor beams are also called as
Headers
Trimmers
Stringers
Rafters

⇒ As per IS : 875, for the purposes of specifying basic wind velocity, the country has been divided into
4 zones
5 zones
6 zones
7 zones

⇒ The effective length of a weld, is taken as the actual length.
minus the size of weld
minus twice the size of weld
plus the size of weld
plus twice the size of weld

⇒ The average shear stress for rolled steel beam section, is.
845 kg/cm2
945 kg/cm2
1025 kg/cm2
1500 kg/cm2

⇒ The diameter of cold driven rivets ranges from
6 mm to 12 mm
12 mm to 22 mm
22 mm to 32 mm
32 mm to 42 mm

⇒ For the structural members exposed to atmosphere, the most unsuitable type of weld is
Slot weld
Butt weld
Intermittent fillet weld
Plug weld

⇒ A riveted joint many experience.
tearing failure of plates
bearing failure of plates
bearing failure of rivets
all the above.

⇒ The sway bracing is designed to transfer
2Vi % of the top panel wind load to bottom bracing
10% of the top panel wind load to bottom bracing
25% of the top panel wind load to bottom bracing
50% of the top panel wind load to bottom bracing

⇒ A major beam in a building structure, is known as.
a girder
a floor beam
a main beam
all the above.

⇒ In the cross-section of a weld, throat is the
minimum dimension
average dimension
maximum dimension
none of the above

⇒ In a structure generally wires and cables are used as
Compression member
Tension member
Compression or tension
To resist shear stresses only

⇒ If the depth of two column sections are equal, then the column splice is provided.
with filler plates
with bearing plates
with filler and hearing plates
none of these.

⇒ The permissible stress to which a structural member can be subjected to, is known as.
bearing stress
working stress
tensile stress
compressive stress

⇒ The internal pressure coefficient on walls for buildings with large permeability is taken as
± 0.2
±0.5
± 0.7
0

⇒ The web crippling due to excessive bearing stress can be avoided by
increasing the web thickness
providing suitable stiffeners
increasing the length of the bearing plates
none of the above

⇒ For a steel grillage footing to support two unequal column loads.
line of action of the resultant of two column loads, is made to coincide with the centre of gravity of the base of the footing
trapezoidal shape is used for the base footing
bending moment under the columns are kept equal to the bending moment between to two columns
all the above.

⇒ If the loaded length of span in meters of a railway steel bridge carrying a single track is 6 m, then impact factor is taken as
0
0.5
between 0.5 and 1.0
1.0

⇒ The size of a butt weld is specified by
Throat thickness
The effective throat thickness
Thickness of thickest part joined
None of the above

⇒ Maximum permissible slenderness ratio of compression members which carry dead and superimposed load, is.
350
250
180
80