Question is ⇒ An ideal Op-amp is an ideal, Options are ⇒ (A) voltage controlled current source, (B) voltage controlled voltage source, (C) current controlled current source, (D) current controlled voltage source, (E) , Leave your comments or Download question paper.

Question is ⇒ An ideal Op-amp is an ideal, Options are ⇒ (A) voltage controlled current source, (B) voltage controlled voltage source, (C) current controlled current source, (D) current controlled voltage source, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	An ideal Op-amp is an ideal
A.	voltage controlled current source [Wrong Answer]
B.	voltage controlled voltage source [Correct Answer]
C.	current controlled current source [Wrong Answer]
D.	current controlled voltage source [Wrong Answer]
View Answer 5 -8 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A junction Field Effect Transistor can operate in
depletion mode only
enhancement mode only
depletion and enhancement modes
neither depletion nor enhancement modes

⇒ In the circuit of the given figure, V_{05 V
3.1 V
2.5 V
0}

⇒ Which of the following statement number is not valid in Basic
12
521
662512
99999

⇒ In a colour TV receiver, the function of comb filter is
to pass only the clusters of monochrome signal energy while blocking chrome signals
to pass only chrome signals and block monochrome signals
to block both monochrome and chrome signals
none of the above

⇒ An MTI radar operating at 5 GHz has a PRF of 800 pps. The lowest blind speed is
48 m/s
96 m/s
192 m/s
24 m/s

⇒ A single phase energy meter has the rating 1200 resolutions/ kWh. If a 500 W electric gadget is used for 4 hours, the energy meter will make
1200 revolutions
1800 revolutions
2100 revolutions
2400 revolutions

⇒ As regards ferromagnetic Curie temperature Q_f and paramagnetic curie temperature θ
Q_f > θ
θ > Q_f
θ equal to or less than Q_f
θ may be equal to less than or more Q_f

⇒ The circuit shown depic
voltage series negative feedback
voltage shunt negative feedback
current series negative feedback
current shunt negative feedback

⇒ The contents of the program counter after the call operation wil
(30F0)_H
(40F0)_H
(50F0)_H
(60F0)_H

⇒ CMRR of an op-amp is about 0.1.
TRUE
FALSE

⇒ Piezoelectric materials serves as a source of
microwaves
ultrasonic waves
musical waves
resonant waves

⇒ Line of sight transmission is used in
radio frequencies below 1 MHz
VHF only
audio signals only
VHF and UHF

⇒ A signum function is
zero for t greater than zero
zero for t less than zero
unity for t greater than zero
2∪(t) - 1

⇒

Assertion (A): Industrial robots improve productivity.

Reason (R): Robots can handle monotonous and complex jobs without error in operation.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒

Assertion (A): The exponential form of Fourierserie
Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ The circumference of an electron orbit is equal to integer times the wavelength of electron.
TRUE
FALSE

⇒ In class C operation of an amplifier circuit, the collector current exists for
360° of input wave
180° of input wave
more than 180° of input wave
less than 180° of input wave

⇒ An op-amp has
low input and output impedance
low input impedance and high output impedance
low output impedance and high input impedance
high output impedance and high input impedance

⇒

Match the following:

	List I (Octal)		List II (Decimal number)
A.	35	1.	53
B.	65	2.	62
C.	54	3.	29
D.	76	4.	44

A-4, B-3, C-2, D-1
A-1, B-2, C-3, D-4
A-2, B-3, C-1, D-4
A-3, B-1, C-4, D-2

⇒ The upper end of the d.c. load line is called the __________ point and the lower end is the __________ point.
cut off, saturation
saturation, active
saturation, cut off
active saturation

⇒

Assertion (A): The TTL output acts as a current sink in low state

Reason (R): The TTL input current is largest in low state.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ In a three variable K map four adjacent cells give
single variable term
two variable term
three variable term
either (a) or (b)

⇒ A monostable multivibrator is used to generate PWM because it can
differentiator
integrator
voltage-to-frequency converter
generate pulses

⇒ In a series RLC circuit the phase angle θ of impedance Z ∠θ is positive. The circuit will behave as
resistive circuit
RC circuit
RL circuit
either RL or RC circuit

⇒ The advantage of pulse modulation is
the transmitted power can be concentrated into short bursts
the time intervals between pulses can be filled with sample values from other message
pulse wave may obtain appreciable D.C. and low frequency content
all of the above

⇒ Which mode has the lowest cut off frequency in circular wave guides?
TE₀₁
TE₁₁
TE₂₀
TE₂₁

⇒ RS latch can be built with
NOR gates
NAND gates
NOR or NAND gates
none of the above

⇒ Magnesium is alloyed with conducting materials for antenna primarily with the purpose of
increasing efficiency
improving radiative power
reducing weight
increasing density

⇒ Consider the program segment written for 8085 based sys
41
69
44
Indeterminate

⇒ The JFET in the circuit shown in figure has an I_DSS = 10 mA and V_p = -5V. The value of the resistance R_s for a drain current I_DS = 6.4 m
156 Ω
470 Ω
560 Ω
1 kΩ