Question is ⇒ An FM signal with a deviation is passes through the mixer, and has its frequency reduced five fold. The deviation in the output of the mixer is, Options are ⇒ (A) Δ, (B) 5Δ, (C) Δ/5, (D) indeterminant, (E) , Leave your comments or Download question paper.

Question is ⇒ An FM signal with a deviation is passes through the mixer, and has its frequency reduced five fold. The deviation in the output of the mixer is, Options are ⇒ (A) Δ, (B) 5Δ, (C) Δ/5, (D) indeterminant, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	An FM signal with a deviation is passes through the mixer, and has its frequency reduced five fold. The deviation in the output of the mixer is
A.	Δ [Correct Answer]
B.	5Δ [Wrong Answer]
C.	Δ/5 [Wrong Answer]
D.	indeterminant [Wrong Answer]
View Answer 1 -2 Explanation:- Answer : A Discuss it below : Abhimanyu keshari Said on 2022-01-28 22:54:37 Ans ...delta !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ For a BJT if β = 50, I_CEO = 3 μA and I_C = 1.2 mA then I_E
1 mA
1.2 mA
1.3 mA
1.4 mA

⇒ The bandwidth required for amplitude modulation is
half the frequency of modulating signal
equal to the frequency of modulating signal
twice the frequency of modulating signal
four times the frequency of modulating signal

⇒ For matching over a range of frequencies in a transmission line it is best to use
a balun
a broad band directional coupler
double stub
a single stub of adjustable position

⇒ A microprocessor with a 16 bit address bus is used in a linear memory selection configuration. Address bus lines are directly uses as chip selects of memory chips with 4 memory chips the maximum addressable memory space is
64 k
16 k
8 k
4 k

⇒ The number of bits in a nibble is
8
4
2
16

⇒ Which of the following is used in automatic control of street lights?
Thermistor
Photoconductor
Transistor
Varistor

⇒

Assertion (A): In a power divider S_H = 0, S₂₁ = 0.707 = S₃,

Reason (R): In a power divider the input port (i.e., port 1) is matched and incident power is equally divided in output ports 2 and 3

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ In a full wave voltage doubler circuit, the input frequency is 560 Hz. The ripple frequency is
25 Hz
50 Hz
100 Hz
200 Hz

⇒ The two modes of operation of three phase bridge inverters are known as
60° mode and 120° mode
90° mode and 120° mode
120° mode and 180° mode
120° mode and 240° mode

⇒ In a decimal digital computer, the number 127 is stored
1111111
0001 00100111
10001
11000111

⇒ Race condition occurs in
synchronous circuit
asynchronous circuit
combinational circuit
all the Digital circuit

⇒ A full wave rectifier using centre tapped transformer and a bridge rectifier use similar diodes and have equal no load output voltage. Under equal load conditions
Output voltage of bridge rectifier
Output voltage of bridge rectifier will be more than that of other
Output voltage of both will be exactly equal
Output voltage of any one may be more than that of other

⇒ When a peripheral device is not ready for data transfer it will send to the microprocessor a
low READY bit
high READY bit
low or high READY bit depending on whether input or output is activated
none of the above

⇒ Secondary emission results
when temperature of metals is raised to a level above the crystallization temperature
when metals are subjected to strong magnetic fields
when light rays fall on the metal surface
when a high velocity beam of electrons strikes as metal surface

⇒ The number of storage classes in C is
2
3
4
6

⇒ The selectivity of most receivers is determined largely by
sensitivity
characteristics of IF section
antenna direction
all of the above

⇒ The colour subcarrier and sidebands produced by its modulation with the chrominance signals are accommodated in the standard channel width by the process of
frequency adjustment
frequency interleaving
frequency changing
frequency amalgamation

⇒ The kinetic energy of photoelectrons emitted by a photo sensitive surface depends on
intensity of the incident radiation
wavelength of the incident radiation
surface conditions of the surface
angle of incidence of radiation

⇒ Wagner earthing device eliminates
all stray capacitance in the circuit
stray capacitances between components
stray capacitance between detector terminal and ground
mutual coupling between components

⇒ In most of instruments, the controlling torque is provided by
fluid fraction
spring
eddy current
either (a) or (c)

⇒ Parabolic and lens antenna used at
microwave frequency
medium frequency
low frequency
high frequency

⇒ Transit time is considered as significant at
HF
MF
LF
all of the above

⇒ A transistor has a maximum power dissipation of 350 mW at an ambient temperature of 25°C. If derating factor is 2 mW/°C, the maximum power dissipation for 40°C ambient temperature is
300 mW
330 mW
350 mW
380 mW

⇒ In a CE amplifier the ac cut off voltage is 9 V and slope of ac load line is - 0.5 mA/V. The ac saturation current is
9 mA
4.5 mA
3 mA
18 mA

⇒ Drift velocity of electrons is generally less than 1 mm/s.
TRUE
FALSE

⇒ In a radio receiver with simple AGC
the highest AGC voltage is produced between stations
an increase in signal strength produces more AGC
the audio stage gain is normally controlled by AGC
the faster the time constant of AGC, more accurate the output

⇒ In the television system in India, each channel is allowed a bandwidth of
20 MHz
12 MHz
7 MHz
3 MHz

⇒ A 1000 kHz carrier is simultaneously modulated with 300 Hz, 800 Hz and 2 kHz audio sine waves. The frequencies present in the output will be
998 kHz and 1002 kHz
998 kHz, 999.2 kHz, 1000.8 kHz, 1002.0 kHz
998 kHz, 999.2 kHz, 999.7 kHz, 1000.3 kHz, 1000.8 kHz and 1000.2 kHz
none of the above

⇒ In VHS format each video head is tilted from azimuth by
20°
10°
6°
1°

⇒ In a RS flip-flop no change occurs during
prohibited mode
set mode
reset mode
disable mode