Question is ⇒ An ac sinusoidal wave has an rms value of 10 V. The peak to peak value is, Options are ⇒ (A) 10 V, (B) 0 V, (C) 14.14 V, (D) 28.28 V, (E) , Leave your comments or Download question paper.

Question is ⇒ An ac sinusoidal wave has an rms value of 10 V. The peak to peak value is, Options are ⇒ (A) 10 V, (B) 0 V, (C) 14.14 V, (D) 28.28 V, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	An ac sinusoidal wave has an rms value of 10 V. The peak to peak value is
A.	10 V [Wrong Answer]
B.	0 V [Wrong Answer]
C.	14.14 V [Wrong Answer]
D.	28.28 V [Correct Answer]
View Answer 3 -3 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A variable resistance R and capacitive reactance X_C are connected in series. As R is varied, the locus of Z is
a straight line parallel to Y axis in 4th quadrant
a straight line parallel to X axis in 4th quadrant
a straight line parallel to Y axis in second quadrant
a straight line parallel to Y axis in first quadrant

⇒ A string of series connected thyristors needs equalising circuit to
ensure proper firing
ensure proper current division
ensure proper voltage division
none of the above

⇒ A 4 bit synchronous counter uses flip flops with a delay time of 15 ns each. The time required for change of state is
15 ns
30 ns
45 ns
60 ns

⇒ In an amplifier, if the output current flows for 120° of the input cycle, the class of amplifier will be
A
B
C
AB

⇒ What will be conversion rate for a counter type A/D converter contains a 4 bit binary ladder and a counter driven by a 2 MHz clock. Then conversion time
125
125 x 10³
125 x 10⁶
None

⇒ If V = 100 ∠ 16°, the (V) is
10 ∠ 32°
10 ∠ 8°
10 ∠ 16°
10 ∠ 4°

⇒ For a half wave rectified voltage, the form factor and peak factor respectively are
1.11 and 2
1.57 and 2
1.11 and 1.11
1.57 and 2

⇒

Assertion (A): Positive feedback is not used in any circuit.

Reason (R): Positive feedback leads to instability.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒ A woofer should be fed from the input through a
low pass filter
high pass filter
band pass filter
band stop filter

⇒ A non-linear element has zero resistance.
TRUE
FALSE

⇒ The A.C. resistance of the emitter diode will be
5.05 Ω
50.5 Ω
505 Ω
5050 Ω

⇒ Two rectangular waveforms of duration t₁ and t₂ seconds are convolved. What is the shape of the resulting waveform?
Triangular
Rectangular
Trapezoidal
Semi-circular

⇒ In body centred cubic structure, comers and centre of the cube are occupied by identical atoms.
TRUE
FALSE

⇒ In the given figure, the curves 1, 2, 3 are respectively
all pass, minimum phase and non-minimum phase functions
minimum phase, all pass and non-minimum phase functions
non-minimum phase, all pass and minimum phase functions
minimum phase, non-minimum phase and all pass functions

⇒ Which of the following statement is false?
The zener diode is uses as a constant voltage source
The SCR is a silicon rectifier with a gate electrode to control when current flows from cathode to anode
The gate electrode in the FET corresponds to the collector in a bipolar transistor
None of the above

⇒ PIL tube means
Picture in Line Tube
Precision in Line Tube
Pairing in Line Tube
Pattern in Line Tube

⇒ A ramp input applied to a unity feedback system results in 5% steady state error. The type number and zero frequency gain of the system are respectively.
1 and 20
0 and 20
0 and 1/20
1 and 1/20

⇒ For the transport lag G(jω) = e^-jωT, the magnitude is always equal to
0
1
10
0.5

⇒ In an ideal junction transistor the impurity concentration in emitter (E ), base (B) and collector (C) is such that
E > B > C
B > C > E
C > E > B
C = E = B

⇒ Figure shows characteristics curves for bipolar transistor. These curves
output characteristics of n-p-n transistor (common base)
output characteristics of p-n-p transistor (common base)
output characteristics of n-p-n transistor (common emitter)
output characteristics of p-n-p transistor (common emitter)

⇒ The current flowing in a certain P-N junction at room temperature is 2 x 10^-7 Amp. When a large reverse biased voltage is applied. Calculate the current flowing when 0.1 volts is applied.
9 μA
10 μA
2 μA
4 μA

⇒ In graphical analysis of BJT amplifier the slope of ac line is more than that of dc load line.
TRUE
FALSE

⇒ A capacitor is considered to be completely charged in __________ time constant.
one
three
five
eight

⇒

Assertion (A): Synchronous counter has higher speed of operation than ripple counter

Reason (R): Synchronous counter uses high speed flip flops.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ An RLC series circuit is underdamped. To make it overdamped, the value of R
has to be increased
has to be decreased
has to be increased to infinity
has to be reduced to zero

⇒ In a purely resistive circuit the instantaneous power varies from zero to maximum twice in each cycle.
TRUE
FALSE

⇒ A signal m(t) = 5 cos 2p 100 t frequency modulates a carrier. The resulting FM signal
0.1 kHz
6 kHz
3.2 kHz
100 kHz

⇒ A meter having 0-1000 μA range and 1000 Ω resistance is required to be changed to 0-100 mA meter. The value of shunt resistance is about
1 Ω
10 Ω
99 Ω
100 Ω

⇒ TE₀₁ mode of propagation of electromagnetic energy
is merely the TE₁₀ mode rotated 90°
is merely the TE₁₀ mode rotated 180°
is the same as TE₁₀ mode
either (b) or (c)

⇒ The first critical frequency nearest the origin of the complex frequency plane for an RL driving point impedance will be
a zero in left half plane
a zero in right half plane
a pole in left half plane
a pole or zero in left half plane