Question is ⇒ A Wien bridge oscillator uses Wien bridge for, Options are ⇒ (A) tuning and phase shift, (B) tuning, (C) phase shift, (D) either tuning or phase shift, (E) , Leave your comments or Download question paper.

Question is ⇒ A Wien bridge oscillator uses Wien bridge for, Options are ⇒ (A) tuning and phase shift, (B) tuning, (C) phase shift, (D) either tuning or phase shift, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	A Wien bridge oscillator uses Wien bridge for
A.	tuning and phase shift [Correct Answer]
B.	tuning [Wrong Answer]
C.	phase shift [Wrong Answer]
D.	either tuning or phase shift [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The pre-emphasis in FM aids in providing extra noise immunity by
emphasizing only the higher frequency components
emphasizing the entire frequency band
emphasizing only the lower frequency band
cutting down the low frequency noise

⇒ Consider the following operation in a computer

Multiplication of scalar
Iversion of matrix
Printing a line of 120 characters on a printer

Which of the above is a subroutine?
1 and 2 only
1 and 3 only
1, 2 and 3
2 only

⇒ In a TV receiver antenna the length of reflector rod
is the same as that of dipole
is less than that of dipole
is more than that of dipole
may be equal, more or less than that of dipole

⇒ Which one of the following statements is wrong. The radar cross-section of a target?
depends on frequency
may be reduced by special coating of non-spherical target
depends on the aspect of target if it is non-spherical
is equal to actual cross-sectional area for small targets

⇒ The circuit shown I/P in the figure repres
Low pass filter
High pass filter
Band Pass filter
Band stop filter

⇒

Assertion (A): Silicon is less sensitive to changes in temperature than germanium.

Reason (R): Cut in voltage in silicon is less than that in germanium.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒ A line of characteristic impedance 400 Ω is terminated by a resistance of 400 Ω. The reflected quantities are
zero
equal to incident quantities
half the incident quantities
double the incident quantities

⇒ The word enhancement mode is associated with
tunnel diode
MOSFET
JFET
photo diode

⇒ Consider the following statements about directional coupler shown in the fi
1 and 2 only
3 and 4 only
1, 2 and 3
2, 3 and 4

⇒ If short-circuited and open circuited impedances are 5 ohms and 20 ohms, then characteristic impedance is
1 ohms
10 ohms
25 ohms
100 ohms

⇒

Assertion (A): The trigger circuit of a CRO is excited by the same signal as Y plates.

Reason (R): The time base generator develops a saw tooth voltage.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒ During day time ionosphere can be considered to be consisting of
D, E, F₁ and F₂ layers
D, E, F₁ layers
D, E, F₂ layers
D and E layers

⇒ A branched duplexer requires
TR tubes
ATR tube
both TR and ATR tube
none of the above

⇒ Which of the following transducers is most suitable for monitoring continuous variations in very fine thickness of a material?
Diaphragm
Capacitor
L.V.D.T.
Piezoelectric crystal.

⇒ In the periodic train of rectangular pulses F₀ = (V₀/T)d
TRUE
FALSE

⇒ In a flip flop which input determines the state to which output will transistion?
Control input
Clock input
Both control and clock input
Either control or clock input

⇒ In a composite filter terminating half sections are used for impedance matching.
TRUE
FALSE

⇒ Consider the expression b = acd (xz). The correct C statement for above expression is
a c d (x * z)
a* c* d* (x z)
a * c * d (x * z)
None of the above

⇒ Which device changes parallel data to serial data?
Decoder
Multiplexer
Demultiplexer
Flip flop

⇒ In a series regulated power supply circuit the voltage gain of pass transistor satisfies the condition
A_v → ∞
1 << A_v → ∞
A_v ≈ 1
A_v << 1

⇒ A transistor amplifier has pole
s₁
s₁ + s₂ + s₃ + s₄
s₁ + s₄
s₄

⇒ In the circuit shown below, the outputs Y₁ and Y₂ for the given initial condition Y₁ = Y₂ = 1 and after four input pulses wil
Y₁ = 1, Y₂ = 0
Y₁ = 0, Y₂ = 0
Y₁ = 0, Y₂ = 1
Y₁ = 1, Y₂ = 1

⇒
Assertion (A): JFET is a voltage controlled device.
Reason (R): The drain current can be controlled by controlling V_GS.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ In the design of a single mode step index optical fiber close to upper cut-off, the single mode operations is NOT preserved if
radius as well as operating wavelength are halved
radius as well as operating wavelength are doubled
radius is halved and operating wavelength is doubled
radius is doubled and operating wavelength is halved

⇒ The communicating capacitor reduces turn on time because
it acts as an open circuit
it allows maximum base circuit to flow
it aids in removing the excess carrier from the base region
none of these

⇒ In the graph shown in the figure, for the tree with branches b, d and f the fundamental loops would inclu
abf, def, bdea
bdc, def, fba
abde, def, cdb
cea, bdea, abbf

⇒ The highest modulation frequencies typically used in FM broadcast is
5 kHz
10 kHz
15 kHz
25 kHz

⇒ A dominant wave is characterised by which of the following?
No attenuation
Lowest cut off wavelength
Highest cut off wavelength
All of the above

⇒ In a tungsten filament lamp
the current at the instant of switching is less than operating current
the current at the instant of switching is more than operating current
the current at the instant of switching is equal to operating current
the current at the instant of switching may be less than or equal to operating current

⇒ A DC voltage source is connected across a series R - L - C circuit. Under steady-state conditions, the applied DC voltage drops entirely across the
R only
C only
L only
R and L combination

Users Also Read
Previous Papers

Aptitude

Reasoning

Gen.Knowledge

Speak English

English / Verbal

Online / Mock Test

Vedic Math