Question is ⇒ A uniform slope was measured by the method of stepping. If the difference in level between two points is 1.8 m and the slope distance between them is 15 m, the error is approximately equal to., Options are ⇒ (A) cumulative, + 0.11 m, (B) compensating, Â± 0.11 m, (C) cumulative, - 0.11 m, (D) none of these, (E) , Leave your comments or Download question paper.

Question is ⇒ A uniform slope was measured by the method of stepping. If the difference in level between two points is 1.8 m and the slope distance between them is 15 m, the error is approximately equal to., Options are ⇒ (A) cumulative, + 0.11 m, (B) compensating, Â± 0.11 m, (C) cumulative, - 0.11 m, (D) none of these, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	A uniform slope was measured by the method of stepping. If the difference in level between two points is 1.8 m and the slope distance between them is 15 m, the error is approximately equal to.
A.	cumulative, + 0.11 m [Correct Answer]
B.	compensating, Â± 0.11 m [Wrong Answer]
C.	cumulative, - 0.11 m [Wrong Answer]
D.	none of these [Wrong Answer]
View Answer 19 -3 Explanation:- Answer : A Discuss it below : Himanshu Gupta Said on 2019-06-28 03:32:48 sloping error is always positive and cumulative in nature. hence no calculation is required for answer this question. !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The apparent error on reversal is.
equal to the actual error
twice the actual error
thrice the actual error
none of these.

⇒ Metallic tapes are made of
Steel
Invar
Cloth and Nvires
Nickel

⇒ Which of the following is not used in measuring perpendicular offsets ?
line ranger
steel tape
optical square
cross staff

⇒ A triangle is said to be well conditioned if none of its angles is less than
20°
30°
45°
60°

⇒ The principle of optics used in the construction of an optical square is
Reflection
Double reflection
Refraction
Double refraction

⇒ A correction for error due to refraction is
0-01 d²m
0-001 d²m
0.01122 d²m
0.078 d²m

⇒ The horizontal angle between the true meridian and magnetic meridian at a place is called
azimuth
declination
local attraction
magnetic bearing

⇒ The type of surveying which requires least office work is
tacheomefry
trigonometrical levelling
plane table surveying
theodolite surveying

⇒ The difference between a level line and a horizontal line is that
level line is a curved line while hori-zontal line is a straight line
level line is normal to plumb line while horizontal line may not be normal to plumb line at the tangent point to level line
horizontal line is normal to plumb line while level line may not be normal to the plumb line
both are same

⇒ The slope correction for a 3° slope for a length of 100 m, is.
-0.11 m
-0.11 m
-1.87 m
-0.137 m

⇒ During levelling if back sight is more than foresight.
The forward staff is at lower point
The back staff is at lower point
The difference in level, cannot be ascertained.
none of these.

⇒ The horizontal angle between true meridian and magnetic meridian, is known.
bearing
magnetic declination
dip
convergence.

⇒ The boundary of water of a still lake, represents.
level surface
horizontal surface
contour line
a concave surface.

⇒ Different grades are joined together by a
compound curve
transition curve
reverse curve
vertical curve

⇒ The bearings of two traverse legs AB and BC are N52° 45' E and N34° 30' E respectively. The deflection angle is.
18Â° 15' E
18Â° 15' N
18Â° 15' W
18Â° 15' L

⇒ Negative errors are caused in chain, when its length is
More than the standard length
Iess than the standard length
Equal to the standard length
Any of the above

⇒ Geodetic surveying is undertaken.
for production of accurate maps of wide areas
for developing the science of geodesy
making use of most accurate instruments and methods of observation
all the above.

⇒ If θ is the slope of the ground and l is the measured distance, the correction is.
2l sin2 Î¸/2
2l cos2 Î¸/2
2l tan2 Î¸/2
2l cot2 Î¸/2.

⇒ Accuracy of 'fix' by two point problem, is.
bad
good
not reliable
unique.

⇒ A lemniscate curve will not be transitional throughout, if its deflection angle, is.
45Â°
60Â°
90Â°
120Â°

⇒ Profile levelling is usually done for determining.
contours of an area
capacity of a reservoir
elevations along a straight line
boundaries of property

⇒ Arbitrary bearing is measured by
Theodolite
Magnetic compass
Astronomical observations
Any of the above

⇒ Mistakes which may produce a very serious effect upon the final results arise due to.
in attention
in experience
carelessness
all of these.

⇒ The error due to bad ranging is
Compensation
Cumulative positive
Cumulative negative
Both (B) and (C) above

⇒ In a perfect prismatic compass.
magnetic axis and geometric axis of the needle coincide
ends of the needle and pivot are in same vertical and horizontal planes
pivot is vertically over the centre of the graduated circle
all the above.

⇒ The real image of an object formed by the objective, must lie.
in the plane of cross hairs
at the centre of the telescope
at the optical centre of the eye-piece
anywhere inside the telescope.

⇒ In an internal focussing type of telescope, the lens provided is
concave
convex
plano-convex
plano-concave

⇒ Pick up the correct specification of Ramsden eyepiece from the following :
it consists of two equal piano convex lenses
the curved surfaces of plano-convex lenses face each other
the two lenses are separated by a distance equal to 2/3 of the focal length of either lens.
all the above.

⇒ Magnetic declination at any place.
remains constant
does not remain constant
fluctuates
changes abruptly.

⇒ The method of finding out the difference in elevation between two points for eliminating the effect of curvature and refraction, is.
reciprocal levelling
precise levelling
differential levelling
flying levelling