Question is ⇒ A thyristor circuit is feeding an R-L load. The turn on time can be reduced by, Options are ⇒ (A) decreasing R, (B) decreasing L, (C) increasing L, (D) decreasing R and L together, (E) , Leave your comments or Download question paper.

Question is ⇒ A thyristor circuit is feeding an R-L load. The turn on time can be reduced by, Options are ⇒ (A) decreasing R, (B) decreasing L, (C) increasing L, (D) decreasing R and L together, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	A thyristor circuit is feeding an R-L load. The turn on time can be reduced by
A.	decreasing R [Wrong Answer]
B.	decreasing L [Correct Answer]
C.	increasing L [Wrong Answer]
D.	decreasing R and L together [Wrong Answer]
View Answer 2 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ For parallel RLC circuit, which one of the following statements is NOT correct?
The bandwidth of the circuit deceases if R is increased
The bandwidth of the circuit remains same if L is increased
At resonance, input impedance is a real quantity
At resonance, the magnitude of input impedance attains its minimum value

⇒ An amplifier with resistive -ve feedback has two left poles in its open loop transfer function. The amplifier
will always be unstable at high frequencies
will be stable for all frequencies
may be unstable, depending on the feedback factor
will oscillate at low frequencies

⇒

Assertion (A): For best results the system of a D'Arsonval galvanometer should be slightly under damped.

Reason (R): Degree of damping affects the time taken by the instrument to come to final position.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒ Which of the following is used as switch?
J-K flip-flop
Master slave J-K flip-flop
T-flip-flop
D-flip-flop

⇒ What is the maximum output voltage from the 741 op-amp?
Zero
Approximately 1 V
Approximately 3 V
Approximately 5 V

⇒ The first machine cycle of an instruction is always
a memory read cycle
a fetch cycle
a input/output read cycle
a memory write cycle

⇒ A meter has a resistance of 1 Ω and full scale deflection current of 1 mA. To convert into an ammeter of 1 A range, the shunt resistance should be
1000 Ω
1 Ω
0.01 Ω
0.001 Ω

⇒ 2's complement representation of a 16 bit number (one sign bit and 15 magnitude bits) is FFFF. Its magnitude in decimal representation is
0
1
32, 767
65, 535

⇒ A transistor amplifier has pole
s₁
s₁ + s₂ + s₃ + s₄
s₁ + s₄
s₄

⇒

Assertion (A): A two byte instruction of 8085 has an operation code in first byte and operand / address in the second byte.

Reason (R): If an instruction is too long it is possible to reduce its length by a number of methods.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ A multilevel decoder is more costly as compared to single level decoder.
TRUE
FALSE

⇒ A 12-bit binary counter has the following state. The octal number represente
677
7163
7128
7183

⇒ For the output F to be 1 in the logic circuit shown, the input combination shoul
A = 1, B = 1, C = 0
A = 1, B = 0, C = 0
A = 0, B = 1, C = 0
A = 0, B = 0, C = 1

⇒ The term VLSI generally refers to a digital IC having
more than 1000 gates
more than 100 gates
more than 1000 but less than 9999 gates
more than 100 but less than 999 gates

⇒ For a second order system the damping factor is varied from 0 to 1. The locus of poles is
a straight line on imaginary axis
a straight line on real axis
a semi circle
a circle

⇒ The drain characteristics of JFET in operating region, are
inclined upwards
almost flat
inclined downwards
inclined upwards or downwards

⇒

Assertion (A): Schering bridge is a low voltage bridge.

Reason (R): Schering bridge is very commonly used for measurement of capacitance.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒ In low pass filter of figure R₀ = 1 Ω and cut off frequency is 1 rad/sec. The values of L and C
1 H and 2 F
1 H and 1 F
2 H and 1 F
1 H and 2 F

⇒ In a 5.6 ohms, ± 10% carbon composition resistor, the colour of the third strip from extreme left is
golden
silver
green
black

⇒ In a Communication system, noise is most likely to affect the signal.
at the transmitter
In the channel
in Information source
at the destination

⇒ In a 3 phase semiconverter, the freewheeling diode comes into operation only if firing angle
is zero
is 60°
is more than 60°
is more than 90°

⇒ In measurements using strain gauge, the dummy strain gauge is used to
compensate for resistance of strain gauge
compensate for change in temperature
compensate for error due to change in voltage of battery
compensate for error in voltmeter

⇒ If the transfer function has zeros only on jω axis or in left half plane, it is a minimum phase function.
TRUE
FALSE

⇒ Which of the following devices uses a helix?
Klystron amplifier
Klystron oscillator
TWT
Both (a) and (b)

⇒ A rectangular waveguide measures 3 x 4.5 cm internally and has a 10 GHz signal propagated in it. Calculate the wave impedance for dominant mode.
130 p
1.3 p
120 p
12 p

⇒ The addressing mode depicted in the given figur
direct
register
register indirect
immediate

⇒ The magnetic moment in units of Bohr magneton of a ferrous ion in any ferrite is
zero
2
4
6

⇒ In a pure sample of silicon
the number of holes and free electrons is always equal
the number of free electrons is more than the number of holes
the number of free electrons and holes is equal at low temperature
the number of free electrons is less than number of holes

⇒ Directive gain of elementary doublet is
100
10
1.5
0.5

⇒ Higher order active filters are used for variable
bandwidth
gain in the pass band
impedance
roll off rate