Question is ⇒ A source is delivering maximum power to a resistance through a network. The ratio of power delivered to the source power,, Options are ⇒ (A) is always 0.5, (B) may be 0.54 or less, (C) may be 0.5 or less, (D) may be 0.5 or more, (E) , Leave your comments or Download question paper.

Question is ⇒ A source is delivering maximum power to a resistance through a network. The ratio of power delivered to the source power,, Options are ⇒ (A) is always 0.5, (B) may be 0.54 or less, (C) may be 0.5 or less, (D) may be 0.5 or more, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	A source is delivering maximum power to a resistance through a network. The ratio of power delivered to the source power,
A.	is always 0.5 [Wrong Answer]
B.	may be 0.54 or less [Correct Answer]
C.	may be 0.5 or less [Wrong Answer]
D.	may be 0.5 or more [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The effect of the inductance of a coil on a constant direct current is that
it does not effect the constant direct current
it decreases the current
it strengthens the current
it causes a higher voltage drop

⇒ If v(t) = 0 for t < 0 and e^-at for t ≥ 0 V(jω) = 1/(a + jω).
TRUE
FALSE

⇒ A hollow rectangular waveguide has dimensions a = 2b. Calculate the amount of attenuation, if the frequency is 3 GHz, and b = 1 cm.
49
47.33
50.33
50

⇒ The band gap of Si at room temperature is
1.3 eV
0.7 eV
1.1 eV
1.4 eV

⇒ Find the FSV (full scale voltage) in a 6 bit R-2R ladder D/A converter has a reference voltage of 6.5 V.
6.4 V
0.1 V
7 V
8 V

⇒ Consider the following stateme
1 only
1 and 2
2 and 3
3 only

⇒ The upper end of the d.c. load line is called the __________ point and the lower end is the __________ point.
cut off, saturation
saturation, active
saturation, cut off
active saturation

⇒ Consider the following statements about transport-lag

It is of non-minimum phase behaviour
It normally exists in thermal, hydraulic and pneumatic systems
It has an excessive phase lag with no attenuation at high frequency

Which of the above statements are correct?
1 only
1 and 2
All
2 and 3

⇒ Which of the following modulation is analog in nature?
PCM
DPCM
DM
PDM

⇒ The output v-i characteristics of enhancement type MOSFET has
only an ohmic region
only a saturation region
an ohmic region at low voltage value and a saturation region at high voltage
a saturation region at low voltage value and an ohmic region at high voltage

⇒ As regards ferromagnetic Curie temperature Q_f and paramagnetic curie temperature θ
Q_f > θ
θ > Q_f
θ equal to or less than Q_f
θ may be equal to less than or more Q_f

⇒ The density of states (i.e. number of states per eV per m³) in the conduction band for energy level E is proportional to
E
E
E^1.5
E²

⇒ For transistor 2 N 338 the manufacturer specifies P_max = 100 mW at 250°C free air temperature and maximum junction temperature of 125°C. Its thermal resistance is
10° C/W
100° C/W
1000° C/W
5000° C/W

⇒ In shot noise
the current rises around mean value
the current rises to peak value, decreases to zero and then again rises
the current may become negative
the current is always less than the mean value

⇒ Two thyristor of same rating and same specifications
will have equal turn on and turn off periods
will have equal turn on but unequal turn off periods
may have equal or unequal turn on and turn off periods
will have unequal turn on and turn off periods

⇒ The V_s is give
8 V
13 V
1 V
4 V

⇒

Assertion (A): For a dielectric, P = ∈₀(∈_r - 1) E.

Reason (R): Dipole moment per unit volume is called polarization of dielectric.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒ The S (sign) flag is set when the contents of accumulator become negative during an operation.
TRUE
FALSE

⇒ The number of spectral component of a cosine wave is
1
0
2
4

⇒ Which of the following parameters of CE circuit has the unit of ohms?
h_ie
h_re
h_fe
h_oe

⇒ In a BJT CE amplifier circuit the value of coupling capacitor should be such that
its reactance is small for the lowest frequency in the input and output
its reactance is high for the lowest frequency in the input and output
its reactance is zero for the lowest frequency in the input and output
its reactance is infinite for the lowest frequency in the input and output

⇒ "Micro-programming" is a technique
for programming the microprocessors
for writing small programs efficiently
for programming the control steps of a computer
for programming output/input

⇒ In a semiconductor avalanche breakdown occurs when
reverse bias exceeds the limiting value
forward bias exceeds the limiting value
forward current exceeds the limiting value
potential barrier is reduced to zero

⇒ For a second order system, the position of poles is in the shaded region shown in the given figure. The variation in damping facto
from 0 to 1
from about 0.3 to 0.7
from 1 to 5
from 0 to 3

⇒ With reference to C programming language, which of the following statements are correct?

An identifier may start with an underscore.
An identifier may end with an underscore.
If is a valid identifier.
The number of significant characters in and identifier is implementation dependent.

Select the correct answer from the codes given below:
1 and 2 only
2 and 3 only
1, 2, 3 and 4
3 and 4 only

⇒ In a step down chopper using pulse width modulation, T_on = 3 x 10^-3 and T_off = 1 x 10^-3 s. The chopping frequency is
333.33
250
500
1000

⇒ For a flexible cable, most suitable insulation is
magnesium oxide
glass fibre
insulating tape
polyvinyl chloride

⇒ The synthesis of minimum function was suggested by
O'Brune
R. Richards
Bott and Duffin
none of the above

⇒ 4 bit ripple counter and 4 bit synchronous counter are made using flip-flop having a propagation delay of 10 ns each. If the worst case delay in the ripple counter and the synchronous counter be R and S respectively, then
R = 10 ns, S = 40 ns
R = 40 ns, S = 10 ns
R = 10 ns, S = 30 ns
R = 30 ns, S = 10 ns

⇒

Assertion (A): In India we use CCIR-B standard

Reason (R): Video signals are frequency modulated.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct