Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | A parallel plate capacitor with air as dielectric has a capacitance C. If the dielectric has a dielectric constant ∈_{r} and the remaining dimensions are the same, the capacitance will be |

A. | C/∈_{r} [Wrong Answer] |

B. | ∈_{r}C [Correct Answer] |

C. | ∈^{2}_{r}C [Wrong Answer] |

D. | ∈^{3}_{r}C [Wrong Answer] |

View Answer
Explanation:-
Answer : BDiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ In a two stage cascade amplifier, each stage has a gain of 10 dB and noise figure of 10 dB. The overall noise factor is

10

1.09

1

10.9

⇒ The total number of leads in MOS controlled thyristor is

2

3

4

2 or 3

⇒ Which one of the following is not a useful quantity for comparing the noise performance of receivers?

Noise figure

Noise temperature

Input noise voltage

Equivalent noise resistance

⇒ A moving coil meter has a shunt of 0.02 Ω resistance. If coil resistance is 1000 Ω and a potential difference of 500 mV is required across it to cause full scale deflection, the current through shunt is

2.5 A

25 A

0.25 A

0.025 A

⇒ A computer monitor uses 180 W in normal operation and 20 W in sleep mode. The computer is on all the 24 hours but is in sleep mode for 18 hours a days. The energy units saved in 30 days are

0.54 units

86.4 units

2.88 units

4.8 units

⇒ The advantage of using crystal oscillator is that it

requires low d.c. supply voltage

works at high frequency

gives high output voltage

gives constant frequency of oscillations

⇒ The network shown in the figure represen

band pass filter

low pass filter

high pass filter

band stop filter

⇒ Complex pole in z-plane is as shown below. This is the pole diagram for ________

Decaying sinusoidal sequence

Growing sinusoidal sequence

Decaying non sinusoidal sequence

Growing non sinusoidal sequence

⇒ Schrodinger wave equation is partial differential equation.

TRUE

FALSE

⇒ A λ/8 section of transmission line is determined of load impedance of (2 -

*j*5) Ω. If characteristic impedance of line is 10 Ω. Then input impedance of line is

10 Ω

(6.9 +

*j*7.24) Ω

(1.75 +

*j*3.098) Ω

(2 -

*j*5) Ω

⇒ The resolution of a 12-bit D/A converter using a binary ladder with + 10V as the full scale output will be

2.44 mV

3.50 mV

4.32 mV

5.12 mV

⇒

**Assertion (A):** Operator has a value 1 ∠ - 90° or 1 ∠ 90°.

**Reason (R):** Operator '*a*' has a value 1 ∠ 120°.

Both A and R are true and R is correct explanation of A

Both A and R are true and R is not the correct explanation of A

A is true but R is false

A is false but R is true

⇒ Z = _______

*C*[

*A*(B + C) +

*D*]

(

*A*B +

*A*C +

*D*)

(

*CA*+

*A*C +

*D*)

none of these

⇒ In the interconnection of ideal sources shown in the figure, it is known that the 60V source is absorbing p

0.416666666666667

13 A

15 A

18 A

⇒ A half wave diode rectifier uses a diode having forward resistance of 50 ohms. The load resistance is also 50 ohms. Then the voltage regulation is

0.2

0.5

1

2

⇒ E

_{G}for silicon is 1.12 eV and that for germanium is 0.72 eV. Therefore it can be concluded that

more number of electron-hole pairs will be generated in silicon than in germanium at room temperature

less number of electron hole pairs will be generated in silicon than in germanium at room temperature

equal number of electron-hole pairs will be generated in both at lower temperatures

equal number of electron-hole pairs will be generated in both at higher temperatures

⇒ State variable formulation is very suitable for computer solution.

TRUE

FALSE

⇒ In a stud mounted SCR, the stud is

in thermal contact with heat sink

insulated from heat sink

in electrical and thermal contact with heat sink

in either electrical or thermal contact with heat sink

⇒ A silicon diode is forward biased and total applied voltage is 5 V. The voltage across

*p*-

*n*junction is

5 V

Slightly less than 5 V

0.7 V

0

⇒ In figure, secondary winding has 40 turns. For maximum power transformer to 2 ohm resistance the number of turns in primar

20

40

80

160

⇒ For a reflection co-efficient of 0.5, the value of SWR is

-1

1

2

3

⇒ In an intrinsic semiconductor, at a given temperature T

the number of electrons-hole pairs generated per second due to thermal motion are equal to the number of electron-hole pairs lost per second due to recombination

the number of electron-hole pairs generated per second due to thermal motion is always less than the number of electron-hole pairs lost per second due to recombination

the number of electron hole pairs generated per second due to thermal motion is always more than the number of electron-hole pairs lost per second due to recombination

any of the above

⇒ The number of address lines in EPROM 4096 x 8 is

2

4

8

12

⇒ The

*P*-type substrate in a conventional

*pn*Junction isolated integrated circuits should be connected to

any where

a dc ground potential

the most positive potential available in the circuit

the most negative potential available in the circuit

⇒ A series RC circuit has R = 5 Ω and C = 10 μF. The current in the circuit is 5 sin 20000

*t*. The applied voltage is

252 sin (20000

*t*+ 45°)

252 sin (20000

*t*- 45°)

252 sin 20000

*t*

252 sin (20000

*t*- 90°)

⇒ The current rating of dc tachogenerator is usually

small

high

medium

either (b) or (c)

⇒ Kell factor is about

5

3

0.7

0.2

⇒ Which two rows represent identical binary numbers?

A second and fourth

Fifth and eight

Third and seventh

Second and third

⇒ In a single phase full wave controlled rectifier using centre tap transformer, the voltage across each half of secondary is V

_{m}sin ω

*t*. The peak inverse voltage is

2 V

_{m}

V

_{m}

0.5 V

_{m}

0.25 V

_{m}

⇒ For input and later stages, BI-FET op-amp use

JFETs and MOSFETs respectively

MOSFETs and JFETs respectively

JFETs and BJTs respectively

BJTs and JFETs respectively