Question is ⇒ A dc voltage source is connected across a series RLC circuit, Under steady state conditions, the applied dc voltage drops entirely across the, Options are ⇒ (A) R only, (B) C only, (C) L only, (D) R and L, (E) , Leave your comments or Download question paper.

Question is ⇒ A dc voltage source is connected across a series RLC circuit, Under steady state conditions, the applied dc voltage drops entirely across the, Options are ⇒ (A) R only, (B) C only, (C) L only, (D) R and L, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	A dc voltage source is connected across a series RLC circuit, Under steady state conditions, the applied dc voltage drops entirely across the
A.	R only [Wrong Answer]
B.	C only [Correct Answer]
C.	L only [Wrong Answer]
D.	R and L [Wrong Answer]
View Answer 1 -6 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A receiver having poor IF selectivity will also have poor
sensitivity
double spotting
blocking
all of the above

⇒ The magnitude response of a normalised Butterworth low pass filter is
linear starting with value of unity at zero frequency and 0.707 at cut off frequency
non linear all through but with values of unity at zero frequency and 0.707 at cut off frequency
linear upto cut off frequency and nonlinear thereafter
nonlinear upto cut off frequency and linear thereafter

⇒ A 3 phase ac regulator uses
3 thyristors
6 thyristors
9 thyristors
12 thyristors

⇒ The use of thermocouple meters for ac measurement leads to a scale which is
linear
square law
logarithmic
exponential

⇒ If the AF voltage is raised to 10 V, while the AM is dropped to 200 Hz, what is the deviation?
10 kHz
15 kHz
20 kHz
40 kHz

⇒ Which binary addition is incorrect?
1101.1 + 1011.1 = 11001.0
101101 + 1101101 + 1100011
0.0011 + 0.1110 + 1.0001
1100.001 + 1011.011 = 10111.100

⇒ A pole zero pattern of a certain filter is shown in figure. This filter mus
LPF
BFP
HPF
APF

⇒ A loop antenna is a commonly used for
radar
direction finding
satellite communication
all of the above

⇒ Compared to a p-n junction with N_A = N_D = 10¹⁴/cm³, which one of the following statements is TRUE for a p-n junction with N_A = N_D = 10²⁰/cm³?
Reverse breakdown voltage is lower and depletion capacitance is lower
Reverse breakdown voltage is higher and depletion capacitance is lower
Reverse breakdown voltage is lower and depletion capacitance is higher
Reverse breakdown voltage is higher and depletion capacitance is higher

⇒ Which one of the following is used as the interface chip for data transmission between 8086 and a 16-bit ADC?
8259
8255
8253
8251

⇒ The ac bridge in figure is balanced. Z₁ = 100∠30°, Z₂ = 150∠0°, Z₃ = 250∠ - 40° Then Z_{4375∠70° Ω
375∠ - 70° Ω
150∠0° Ω
150∠20° Ω}

⇒ For an m-derived filter, attenuation is infinite when f = f_∞.
TRUE
FALSE

⇒ At room temperature kT = 0.03 eV.
TRUE
FALSE

⇒ MCVF telegraphy causes
SSB techniques
pulse modulation
Out of bond signalling
FM

⇒ The first critical frequency nearest the origin of the complex frequency plane for an RL driving point impedance will be
a zero in left half plane
a zero in right half plane
a pole in left half plane
a pole or zero in left half plane

⇒

Assertion (A): The expression E = - ΔV, where E is the electric field and V is the potential is not valid for time varying fields.

Reason (R): The curl of a gradient is identically zero.

Both A and R are individually true and R is the correct explanation of A
Both A and R are individually true but R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒ As regards ∈₀ and ∈_r (absolute and relative permittivity)
both ∈₀ and ∈_r can be interpreted in terms of atomic properties of medium
only ∈_r can be interpreted in terms of atomic properties of medium
only ∈₀ can be interpreted in terms of atomic properties
∈_r has no physical significance

⇒

Assertion (A): When an SCR is conducting, the voltage drop across is about 1 V.

Reason (R): When an SCR is conducting, the junction temperature is about 200°C.

Both A and R are correct and R is correct explanation of A
Both A and R correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ An engineer designs an amplifier to have a voltage gain of 60, but when constructed it only had a gain of 50. Which of the following will increases from this type of operation?
Stability
Bandwidth
Distortion
Input resistance

⇒ In the television system in India, the aspect ratio is
0.16875
0.127777777777778
0.211111111111111
0.170138888888889

⇒ The storage capacity of DSDD disk and DSHD disk are
1.2 MB each
360 KB each
1.2 MB and 360 KB respectively
360 KB and 1.2 MB respectively

⇒ A sheet of bakelite is inserted between the plates of an air capacitor. The capacitance will
increase
decrease
remain the same
may increase or decrease

⇒ A series RC circuit has fixed X_C, and variable R. The current locus is in the first quadrant.
TRUE
FALSE

⇒ If operator 'a' = 1 ∠120° then (1 + a) =
-a
-a²
a
-1

⇒ Which of the following is true about an impulse voltage?
It is a unidirectional voltage
Chopped impulse flashover does not occur
Time taken to rise is equal to time taken to fall
RMS value is always less than 50% of average value

⇒ A wire has a diameter d and resistance R. If the diameter is made 3d, the length and material remaining the same, the new value of resistance will be
R/3
3 R
R/9
9 R

⇒ The impulse response of the DT - LTI system is given be
1 and 2
2 and 3
1 and 3
1, 2 and 3

⇒ The minimum energy of a photon required for intrinsic excitation is equal to
energy of bottom of conduction band
energy of top of valence band
forbidden gap energy
Fermi energy

⇒ A 1 mA meter is to be converted to 1 A ammeter. The meter resistance is 100 Ω. The value of shunt resistance is
0.001 Ω
0.1001 Ω
100 Ω
1000 Ω

⇒ Directive gain of elementary doublet is
100
10
1.5
0.5