Question is ⇒ A high frequency series inverter consists of, Options are ⇒ (A) a number of series inverters in series, (B) a number of series inverters in parallel, (C) a number of parallel inverters in parallel, (D) a number of parallel inverters in series, (E) , Leave your comments or Download question paper.

Question is ⇒ A high frequency series inverter consists of, Options are ⇒ (A) a number of series inverters in series, (B) a number of series inverters in parallel, (C) a number of parallel inverters in parallel, (D) a number of parallel inverters in series, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	A high frequency series inverter consists of
A.	a number of series inverters in series [Wrong Answer]
B.	a number of series inverters in parallel [Correct Answer]
C.	a number of parallel inverters in parallel [Wrong Answer]
D.	a number of parallel inverters in series [Wrong Answer]
View Answer 2 -2 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In a single phase full wave ac regulator using two thyristors only, the gate circuits of the two thyristors
must be isolated
may or may not be isolated
should be preferably, isolated
should not be isolated

⇒ The input to negative clamper has a peak value of V_p. Then in the output the positive and negative peaks are nearly
0 and -2 V respectively
V_p and -V_p respectively
2 V_p and 0 respectively
none of the above

⇒ The mechanical system shown below has its pole(s)
- K/D
- D/K
- DK
0, - K/D

⇒ For a transistor the normal collector voltage is 12 V. If actually it is found to be + 28 V, the trouble could be
R_L is open
R_E is open
C_E is shorted
C_E is open

⇒ In an ac series RLC circuit the maximum phase difference between any two voltages can be
90°
45°
- 90°
180°

⇒ In 8085, out of interrupts given below, one particular interrupts is quite different from others, This interrupt is
RST 5.5
RST 6.5
RST 7.5
none of these

⇒ A constant k low pass filter has f_c = 1000 Hz. At f = 500 Hz, the phase shift is
p
zero
more than p
less than p

⇒

Match the following:

	List I		List II
A.	Silicon	1.	is trivalent
B.	Arsenic	2.	rarely used as semiconductor
C.	Indium	3.	is pentavalent
D.	Germanium	4.	intrinsic semiconductor

A-1, B-2, C-3, D-4
A-4, B-3, C-2, D-1
A-4, B-3, C-1, D-2
A-2, B-1, C-3, D-4

⇒ In figure, the short circuit current through terminal AB wil
0.125
1.5 A
0.0833333333333333
0.0416666666666667

⇒ A wire has a resistance R ohm. If another wire of the same material and same weight has double the diameter (as compared to the first wire), the resistance of the second wire will be
0.5 R
0.25 R
0.125 R
R/16

⇒ What is meant by "continuous collector current" in BJT?
Maximum collector current
Current at Quiescent condition
Leakage current
Junction Capacitance charging and discharging current

⇒ In oscillators class C operation is preferred because
is most efficient
has frequency stability
gives larger output
it produces nearly square waves

⇒ For a paramagnetic material, susceptiblity increases with increasing temperature.
TRUE
FALSE

⇒ Consider the following statements: The radar pulse must be flat topped to

allow accurate range measurement
allow good minimum range
prevent frequency changes in magnetron
make the returned echoes easier to distinguish from noise.

Which of the above are correct?
1, 2, 3, 4
1, 2, 3
1, 2
1, 3, 4

⇒ PROM is
Permanent Read Only Memory
Polarized Read Only Memory
Positive Read Only Memory
Programmable Read Only Memory

⇒ Alternating current can induce voltage because it has magnetic field which is
constant
time varying
stronger field than D.C.
closed loop nature.

⇒ In 8085 microprocessor, how many lines are there in data bus?
6
8
2
16

⇒

Assertion (A): An op-amp amplifier can amplify dc signal

Reason (R): An op-amp amplifier is a direct coupled amplifier

Both A and R are correct and R is correct explanation for A
Both A and R are correct but R is not correct explanation for A
A is correct R is wrong
A is wrong R is correct

⇒ The function shown in the fig
impulse function
signum function
unit step function
none of the above

⇒ For an RC admittance function
the lowest critical frequency is a zero
the highest critical frequency is a pole
the lowest critical frequency is zero and the highest critical frequency is a pole
the lowest critical frequency is a pole

⇒ A network is said to be two port network if there is

no independent source in the network
no dependent source in the network
non-linear component in the circuit
no external connection exist between I/P and 0/P

1, 2, 3
3, 4, 2
1, 3, 4
4, 3, 1, 2

⇒ For an op-amp source follower circuit
input and output voltages have same magnitude
output and input voltages are in phase
output and input voltages are in phase but have different magnitudes
output and input voltages have same magnitude and are in phase

⇒ Decimal 8 in excess-3 code =
1000
1001
1011
1111

⇒ A FM signal with modulation index M_f is passed through a frequency doubler. The wave in the output of the doubler will have modulation index of
M_f
M_f/2
2M_f
UM_f

⇒ An average responding rectifier type electronic voltmeter has its scale calibrated in terms of rms value of sine wave. If 100 V peak value square wave is fed to this voltmeter, the reading will be
111 V
100 V
90.9 V
70.7 V

⇒

Assertion (A): Points in the s plane at which function G(s) is not analytic are called singular, points.

Reason (R): Singular points at which the function G(s) or its derivative approach infinity are called poles.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒ Which of these commutation methods uses an auxiliary SCR?
Class A
Class B
Class C
Class D

⇒ The maximum counting range of a four stage counter using IC 74193 is
0 to 1023
0 to 4093
0 to 65535
0 to 131071

⇒ Consider the following statement in FORTRAN 77 2 values could be read and stored asX (0), Y (0)
4 values could be read and stored asX (0), Y (0), X (2), Y (2)
6 values could be read and stored as X (0), Y (0), Y (2), X (3), Y (3)
none of the above

⇒ The minimum number of 2 input NAND gates required to implement Boolean function A B C is A, B, C are available is
2
3
5
6