Question is ⇒ A feeder, in a transmission system, feeds power to, Options are ⇒ (A) distributors, (B) generating stations, (C) service mains, (D) all of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ A feeder, in a transmission system, feeds power to, Options are ⇒ (A) distributors, (B) generating stations, (C) service mains, (D) all of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	A feeder, in a transmission system, feeds power to
A.	distributors [Correct Answer]
B.	generating stations [Wrong Answer]
C.	service mains [Wrong Answer]
D.	all of the above [Wrong Answer]
View Answer 21 -18 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Electro-mechanical voltage regulators are generally used in
reactors
generators
transformers
all of the above

⇒ The effective resistance of a conductor will be the same as 'ohmic resistance' when
power factor is unity
current is uniformly distributed in the conductor cross-section
voltage is low
current is in true sine wave form

⇒ In the design of a distributor which of the following is the major consideration ?
Voltage drop
Current carrying capacity
Frequency
kVA of system

⇒ The presence of ozone due to corona is harmful because it
reduces pawer factor
corrodes the material
gives odour
transfer energy to the ground

⇒ Which of the following equipment is used to limit short-circuit current level in a substation ?
Isolator
Lightning switch
Coupling capacitor
Series reactor

⇒ If the height of transmission tower is increased, which of the following; parameters is likely to change ?
Capacitance
Inductance
Resistance
All of the above

⇒ Transmission line insulators are made of
glass
porcelain
iron
P.V.C.

⇒ When a conductor carries more current on the surface as compared to core, it is due to
permeability variation
corona
skin effect
unsymmetrical fault

⇒ For which of the following equipment current rating is not necessary ?
Circuit breakers
Isolators
Load break switch
Circuit breakers and load break switches

⇒ In transmission and distribution system the permissible voltage variation is
± 1 percent
± 10 percent
± 20 percent
± 30 percent

⇒ In a distribution system major cost is that of
earthing system
distribution transformer
conductors
meters

⇒ Floating neutral, in 3-phase supply, is undesirable because it causes
low voltage across the load
high voltage across the load
unequal line voltages across the load
none of the above

⇒ Basically the boosters are
synchronous motors
capacitors
inductors
transformers

⇒ 310 km line is considered as
a long line
a medium line
a short line
any of the above

⇒ A synchronous condenser is generally installed at the of the ____ transmission line
receiving end
sending end
middle
none of the above

⇒ A lightning arrester is usually located nearer to
transformer
isolator
busbar
circuit breaker

⇒ For which of the following, the excitation control method is satisfactory ?
Low voltage lines
High voltage lines
Short lines
Long lines

⇒ System grounding is done so that
inductive interference between power and communication circuits can be controlled
the floating potential on the lower voltage winding for a transformer is brought down to an insignificant value
the arcing faults to earth would not set up dangerously high voltage on healthy phases
for all above reasons

⇒ Resistance grounding is used for voltage between
33 kV to 11 k V
11 kV to 33 kV
33 kV to 66 kV
none of the above

⇒ Owing to skin effect
current flows through the half cross-section of the conductor
portion of the conductor near the surface carries more current and core of the conductor carries less current
portion of the conductor near the surface carries less current and core of the conductor carries more current
any of the above

⇒ If string efficiency is 100 percent it means that
potential across each disc is zero
potential across each disc is same
one of the insulator discs is shorted
none of the above

⇒ The current drawn by the line due to corona losses is
non-sinusoidal
sinusoidal
triangular
square

⇒ Which of the following is neglected in the analysis of short transmission lines ?
Series impedance
Shunt admittance
I²R loss
None of the above

⇒ Overhead lines generally use
copper conductors
all aluminium conductors
A.C.S.R. conductors
none of these

⇒ The square root of the ratio of line impedance and shunt admittance is called the
surge impedance of the line
conductance of the line
regulation of the line
none of the above

⇒ The wooden poles well impregnated with creosite oil or any preservative compound have life
from 2 to 5 years
10 to 15 years
25 to 30 years
60 to 70 years

⇒ Overhead system can be designed for operation upto
11 kV
33 kV
66 kV
400 kV

⇒ Which of the following bar schemes is the most expensive ?
Double bus-bar double breaker
Ring bus-bar scheme
Single bus-bar scheme
Main and transfer scheme

⇒ In aluminium conductors, steel core is provided to
compensate for skin effect
neutralise proximity effect
reduce line inductance
increase the tensile strength

⇒ Transmission voltage of 11 kV is normally used for distances upto
20-25 km
40-50 km
60-70 km
80-100 km