Question is ⇒ A dummy bridge employing strain gauge provides ____, Options are ⇒ (A) linearity, (B) stability, (C) temperature compensation, (D) none of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ A dummy bridge employing strain gauge provides ____, Options are ⇒ (A) linearity, (B) stability, (C) temperature compensation, (D) none of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	A dummy bridge employing strain gauge provides ____
A.	linearity [Wrong Answer]
B.	stability [Wrong Answer]
C.	temperature compensation [Correct Answer]
D.	none of the above [Wrong Answer]
View Answer 4 -3 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Various adjustments in an energy meter include
light load or friction
lag and creep
overload and voltage compensation
temperature compensation

⇒ An ammeter is a
secondary instrument
absolute instrument
recording instrument
integrating instrument

⇒ Which of the following cannot be measured by multimeters ?
Frequency
Current
Voltage
Resistance

⇒ The error, when reading at half-scale in an instrument, is
equal to half of full-scale error_
equal to full-scale error
less than full-scale error
greater than full-scale error

⇒ The total power delivered to a threephase load is equal to
algebraic sum of two-wattmeter readings
algebraic difference of two-watt meters readings
vectorial sum of two-wattmeter readings
vectorial difference of tvvo-watt meters readings

⇒ Aluminium is selected as the material for rotating disc of energy meter because
it is good conductor
it is light
it is indigenously available
all of the above reasons

⇒ The electrical power to a meggar is provided by
battery
permanent magnet D.C. generator
A.C. generator
any of the above

⇒ Which of the following can be measured by Solometers' ?
Thermal radiations
Electrical signals
Optical inputs
Temperature inputs

⇒ Meggar is used to measure
breakdown voltage of insulation
earth resistance
insulation resistance
none of above

⇒ For measuring an unknown electrical quantity, select the meter with
highest range and work down
lowest range and work up
with middle range and work up and down on trial and error basis
any of the above

⇒ Which of the following can be measured by the use of a Schering bridge ?
Dielectric loss and power factor
Frequency and capacitance
Variable resistances
All of the above

⇒ In a 3-phase power measurement by two wattmeter method, both the wattmeters had identical readings. The power factor of the load was
unity
0.8 lagging
0.8 leading
zero

⇒ A potentiometer works on
heating effect
magnetic effect
electro-magnetic induction
none of the above

⇒ Which of the following is an analogue transducer ?
Strain gauge
Thermistor
LVDT
All of the above

⇒ If voltage supply to the energy meter is more than the rated value, energy meter will run
slow
fast
either of the above
none of the above

⇒ The operating voltage of a meggar is about
6 V
12 V
40 V
100 V

⇒ ____ can measure only pressure.
Displacer
Radioactive method
Belt type meter
Bubble gauge method

⇒ Most sensitive galvanometer is
elastic galvanometer
vibration galvanometer
Duddle galvanometer
spot ballistic galvanometer

⇒ Which of the following instruments may be used to measure D.C. voltage accurately ?
Moving iron type instrunaent
Movnig coil type instrument
Electrodynatnic type instrument
None of the above

⇒ The advantage of digital tape recording is that
it gives highly accurate results
it is insensitive to tape speed
it needs simple data conditioner
information can be directly fed to digital computers for processing and control

⇒ The meter constant of single phase energy meter is expressed in terms of
revolutions/kWh
kW/kWh
amps/kW
Volts/kWh

⇒ Control springs are made up of
phosphor bronze
copper
silver
steel

⇒ A power factor meter has _____ control springs.
one
two
four
no

⇒ A Weston frequency meter is
moving coil in.strument
moving iron instrument
dynamometer instrument
none of the above

⇒ Thermistors have ____ temperature coefficient.
low and positive
high and positive
low and negative
high and negative

⇒ Which of the following is the merit of a moving iron instrument ?
It can be used under severe overload conditions
It has linear scale
It can be used at high frequencies
Its current sensitivity is high

⇒ Meggar is operated by
internal battery
an external voltage source
an internal hand driven generator
none of the above

⇒ By a 'Rotameter' we can measure
specific gravity
viscosity
flow
rotation

⇒ Damping in an instrument provides
counter torque to deflection torque
good accuracy
braking action on a meter pointer
starting torque on the meter pointer

⇒ When the damping of an instrument is adjusted to enable the pointer to rise quickly to its deflected position without overshooting, in that case the instrument is said to be
under-damped
over-damped
dead beat
off beat