Question is ⇒ A differentially compounded dc motor is running at rated speed. If the series field winding of the motor gets short circuited, the speed of the motor will, Options are ⇒ (A) remain unaltered., (B) increase., (C) decrease., (D) be zero., (E) , Leave your comments or Download question paper.

Question is ⇒ A differentially compounded dc motor is running at rated speed. If the series field winding of the motor gets short circuited, the speed of the motor will, Options are ⇒ (A) remain unaltered., (B) increase., (C) decrease., (D) be zero., (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	A differentially compounded dc motor is running at rated speed. If the series field winding of the motor gets short circuited, the speed of the motor will
A.	remain unaltered. [Wrong Answer]
B.	increase. [Wrong Answer]
C.	decrease. [Correct Answer]
D.	be zero. [Wrong Answer]
View Answer 7 -2 Explanation:- Answer : C Discuss it below : Naini Ramesh Said on 2022-12-17 23:20:44 Speed will decrease..ans c is exactly correct... because in diffential compound motor flux is substracted from shunt flux..if series flux is zero.. resulted flux will increase.. Ragavesh kolamuskar Said on 2019-04-12 05:49:49 Speed will increse !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ It is desirable to eliminate 5th harmonie voltage from the phase voltage of an alternator. The coils should be short pitched by an electrical angle of
30°
36°
72°
18°

⇒ Variation in dc excitation of a synchronous motor causes variation in
speed of motor
power factor
armature current
both armature current and power factor.

⇒ A series motor is working drawing a load current of 1 A from the lines. If now the load is reduced such that the current drawn is halved, the speed of the machine (neglecting the saturation and armature resistance) would be
unchanged.
reduced by 50%.
reduced by 100%.
increased by 100%

⇒ A dc series motor is best suited for driving
line shafting, blowers and fans.
machine tools.
shear and punches.
cranes and hoists

⇒ Consider the following statements connection with electromagnetic waves:
1. Conducting medium behaves like an open circuit to the electromagnetic field.
3. At radio and microwave frequencies the relaxation tOne is much less than the period.
3. In loss-less dielectric the relaxation time is infinite.
4. Intrinsic impedance of a perfect dielectric medium is a pure resistance.
Which of the above statements is correct?
1 only.
1 and 2 only.
2 and 3 only
2, 3 and 4.

⇒ Can a 50Hz transformer be used for 25 Hz, if the input voltage is maintained constant at the rated value corresponding to 50 Hz?
Yes, since the voltage is constant current tevel will not change.
No, flux will be doubled which will drive the core to excessive saturation
No. owing to decreased resistance of transformer, input current will he doubled at the load,
Yes, at constant voltage, insulation will not be overstressed

⇒ The number of poles on turbo-alternator is usually
2
4
6
8

⇒ Aluminium is not used as winding wire in dc machine armature as it
is costlier
is of low resistivity
is of lower thermal conductivity
requires large winding space

⇒ Which of the following devices can be used as a phase advancer?
3-phase induction motor squirrel cage type.
3-phase induction motor slip-ring type.
Synchronous motor working at leading power factor.
Synchronous motor working at lagging power factor.

⇒ In induction motor, air gap power is 10 kW and mechanically developed power is 8 kW. What are the rotor ohmic losses?
1 kW
3 kW
2 kW
0.5 kW

⇒ In a motor-convertor the commutator machine acts as
a generator only
a convertor only
both as generator and as convertor
as a transformer only.

⇒ A 3-phase induction motor draws 1,000 kVA at a pf of 0.8 lag. A synchronous condenser is connected in parallel to draw an additional 750 kVA at a power factor of 0.6 lead. The pf of the total load supplied by the mains is
unity.
0.707 lead.
0.6 lag.
zero.

⇒ Which part of transformer is subjected to maximum heating?
Frame.
Core.
Winding.
Oil.

⇒ Two 10 kV/440 V 1-phase transformers of ratings 600 kVA and 350 kVA are connected in parallel to share a load of 800 kVA. The reactances of the transformers, referred to secondary side are 0.0198 Ω and 0.0304 Ω respectively, (resistance negligible). The load shared by two transformers will be
484.5 kVA and 315.5 kVA.
315.5 kVA and 484.5 kVA.
533 kVA and 267 kVA.
267 kVA and 533 kVA.

⇒ In a synchronous alternator, which of the foliòving coils will have emf closer to sine wave form?
Concentrated winding in ful pitch coils.
Cncentrated winding in short pitch coils.
Distributed winding in full pitch coils.
Distributed winding in short pitch coils.

⇒ The running winding of a single phase motor is found earthed on testing. The most probable location of ground fault is at the
end connection
end terminals
slot edge where coil enters or comes out of the slot
anywhere on the winding inside a slot

⇒ Concentrated winding has
one coil per phase.
two coils per phase.
one coil per pair of poles per phase.
one coil side per pole pair per phase.

⇒ While starting a 3-phase synchronous motor by induction motor action, very high emf is induced in the field winding. The damage to the insulation of field winding and slip-rings can be avoided by
splitting the field winding in several sections
short circuiting the field winding through field discharge resistance.
either (a) or (b).
none of these.

⇒ If a resistance is connected across the armature of a dc series motor, its speed for a constant load torque will
increase.
decrease.
remain unaltered.
become zero.

⇒ Two 3-phase transformers are to be connected for parallel operation. Which one of the following arrangements is impossible?
Transformer Δ; primary Y; secondary Y
Transformer B; primary Δ; secondary Δ
Transformer Δ; primary Δ; secondary Y
Transformer B; primary Δ; secondary Δ
Transformer Δ; primary Y; secondary Δ
Transformer B: primary Δ; secondary Y
Transformer Δ; primary Δ; secondary Δ
Transformer B; primary Δ; secondary Δ

⇒ A three-phase 50 Hz, li kV and 37.5 MW at 0.9 p.f. capacity synchronous generator has its stator bore diameter of 765 cm arid an axial core length of 80cm. For which power plant this generator is suitable?
Thermal coal fired plant
Hydroelectric power plant.
Nuclear power plant.
Pumped storage power plant.

⇒ For starting a 3-phase induction motor ____ winding is to be connected to 3-phase ac supply.
rotor
stator
both stator and rotor
none

⇒ Consider the following statements regarding the starting of a dc shunt motor:
1 External field resistance should be minimum.
2 External field resistance should be maximtim.
3 Reduced voltage should he applied to the armature.
4 Increased voltage should be applied to the armature.
Of these statements
1 and 3 are correct.
1 and 4 are correct.
2 and 3 are correct.
2 and 4 are correct.

⇒ The rms value of a sine wave is loo A. Its peak value is
70.7 A
141 A
150 A
282.8 A

⇒ Switched reluctance motor means
salient pole synchronous motor without excitation winding
a stepper motor with salient poles
synchronous motor with salient poles on stator and rotor.
a stepper motor with closed loop control and with rotor position sensor

⇒ 1f an induction motor hums during starting up. the possible cause could be
open circuit
unequal phase resistance
inter-turn short circuit on rotor
any of the above

⇒ ____ motor is usually employed in motor-generator sets.
Squirrel cage induction
Slip-ring induction
Synchronous
Commutator

⇒ In dc machines, the air gap flux distribution in space at no load is
sinusoidal,
triangular.
flat topped
pulsating.

⇒ The torque developed in an induction motor is nearly proportional to
1/V
V
V²
none of these

⇒ A coil having a resistance of 5 ω and inductance of 0.1 H is connected in series with a condenser of capacitance 50 pF. A constant alternating voltage of 200 V is applied to the circuit. The voltage across the coil at resonance is
200 volts
1,788 volts
1,800 volts
2,000 volts