Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | A conditionally stable system is stable for the value of gain between two critical values. It is unstable if |

A. | the gain is increased beyond upper critical value [Wrong Answer] |

B. | the gain is decreased below lower critical value [Wrong Answer] |

C. | both (a) and (b) [Correct Answer] |

D. | none of the above [Wrong Answer] |

View Answer
Explanation:-
Answer : CDiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ Which of the following statement regarding waveguides is

*incorrect*?

At waveguide can be coupled to a coaxial cable

At frequencies below the cut off value the wave progresses across the waveguide after total reflections

Waveguides are usually air filled hollow conducting metallic tubes for transmitting UHF and microwaves

Waveguides can handle large power at UHF and microwaves

⇒ Consider the signal S(

*t*) shown bel

8

12

16

18

⇒ When a lead acid cell discharges, the specific gravity of electrolyte increases.

TRUE

FALSE

⇒ A linear discrete time system has the char. equation

*z*

^{3}- 0.81

*z*= 0, the system is

stable

marginally stable

unstable

stability cannot be assessed from the given information

⇒ The reason for glitches on the outputs of decoding gates on a synchronous counter is

FFs changing states together

FFs changing states one at a time

AND gates not functioning properly

none of the above

⇒ In a loss line R

_{L}< Z

_{0}, then

Reflection coefficient is zero

Reflection coefficient is ∞

Reflection coefficient is negative

Reflection coefficient is positive

⇒ In the basic series inverter circuit, the source current has

low harmonic content

high harmonic content

low or high harmonic content depending on firing angle

zero harmonic content

⇒ The total power radiated from an antenna system is determined by imagining that the antenna is at the centre of a very large

sphere

rectangle

square

ellipse

⇒ The pointer of an indicating instrument should be

very light

very heavy

neither heavy nor light

heavy

⇒ In a 4 bit weighted resistor D/A converter, the resistor value corresponding to LSB is 32 kΩ. The resistor value corresponding to MSB will be

32 KΩ

16 KΩ

8 KΩ

4 KΩ

⇒ A radar beacon is a small radar set having a receiver, a separate transmitter and an antenna.

TRUE

FALSE

⇒ A square in which each (

*i*,

*j*)

^{th}element of matrix is equal to the negative of the conjugate complex of (

*j*,

*i*)

^{th}element, is called

Hermitian matrix

Skew symmetric matrix

Conjugate anti-symmetric matrix

Skew-Hermitian matrix

⇒ Which of the following is a valid logical expression in Pascal?

2.5 : = A

(A + B) < < (C + D)

A = < B

A > = B

⇒ Which of the following is not a necessary advantage of negative feedback system?

Feedback improves speed of response

Feedback improves stability

Feedback reduces effect of variations in system parameters

Feedback reduces the effect of external disturbances

⇒ The inductance of a twin feeder used to connect antenna to TV receiver is about

0.2 μ H/m

0.6 μ H/m

1.6 μ H/m

10 μ H/m

⇒ A current of 1 A in the coil of an iron cored electromagnet cause a flux density of 0.2.T. If the current is 2 A, B=

0.2 T

0.4 T

0.4 T or less

0.4 T or more

⇒ In the given figure, the input frequency is such that R = X

_{C}.

*v*

_{0}lags

*v*

_{i}by 45°

*v*

_{0}lags

*v*

_{i}by 90°

*v*

_{0}leads

*v*

_{i}by 45°

*v*

_{0}leads

*v*

_{i}by 90°

⇒ Which of the following microphones has maximum distortion?

Ribbon

Condenser

Crystal

Carbon

⇒

**Assertion (A):** In Darlington pair, the overall β is product of individual β_{s}

**Reason (R):** The voltage gain of a base driven amplifier is equal to ac collector voltage divided by ac base voltage

Both A and R are correct and R is correct explanation for A

Both A and R are correct but R is not correct explanation for A

A is correct R is wrong

A is wrong R is correct

⇒ The current source in figure, can be replace

a voltage source of 20 V in series with 5 ohm resistance

a voltage source of 16 V in series with 4 ohm resistance

a voltage source of 20 V in series with 4 Ω resistance

a voltage source of 16 V in series with 5 Ω resistance

⇒ In the following astable multivibrator circuit, which properties of

*v*

_{0}(

*t*) depends on R

_{2Only the frequencyOnly the amplitudeBoth the amplitudeNeither the amplitude nor the frequency}

⇒ Which of the following statement about receivers is false?

Double conversion is used to improve image rejection

Double conversion is used to improve selectivity

Variable sensitivity is used to improve selectivity

Variable sensitivity is used to eliminate selective fading

⇒ The self inductances of two coils are 27 H and 3 H. If the winding or coils is such that 50% of flux of one links the other, the mutual inductance is

30 H

24 H

9 H

4.5 H

⇒ The chip 8254 is a 40 pin programmable interval timer. The number of its independent 16 bit counters is

2

3

4

5

⇒ A signal

*f*(

*t*) = cos 10p

*t*+ 3 cos 4p

*t*is instantaneously sampled. The maximum allowable value of sampling interval T

_{s}in sec is

1 / 4 sec

1 / 8 sec

1 / 8p sec

1 / 10 sec

⇒ An electromagnetic wave incidents on a perfect insulator at an angle. If the wave is not entirely parallel polarized, then

the reflected wave will be entirely polarized parallel to the plane of incidence

there will be no reflection

the reflected wave will be entirely polarized perpendicular to the plane of incidence

any of the above

⇒ The range of visible light is

300 to 2000 Å

200 - 4000 Å

4000 to 7700 Å

more than 10000 Å

⇒ In saturation region JFET acts like a

bipolar device

short circuit

switch

resistance

⇒ In satellite communication, frequency modulation is used because satellite channel has

small bandwidth and negligible noise

large bandwidth and severe noise

maximum bandwidth and minimum noise

high modulation index

⇒ In figure, the current through

*R*is 1 A when V

_{A}= 0 and V

_{B}= 15V. If both V

_{A}and V

_{B}are increased by 15V each, current through R wil

0.0416666666666667

0.5 A

0.125

0.33 A