Question is ⇒ A component that opposes the change in circuit current is, Options are ⇒ (A) resistance., (B) capacitance., (C) inductance., (D) conductance., (E) , Leave your comments or Download question paper.

Question is ⇒ A component that opposes the change in circuit current is, Options are ⇒ (A) resistance., (B) capacitance., (C) inductance., (D) conductance., (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	A component that opposes the change in circuit current is
A.	resistance. [Wrong Answer]
B.	capacitance. [Wrong Answer]
C.	inductance. [Correct Answer]
D.	conductance. [Wrong Answer]
View Answer 10 -7 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which of the following statements about Schrage motor is incorrect?
it gives normally speed range of 3 to i but much speed ranges upto 15 to I and higher may also be obtained.
It is cheaper than the slip-ring induction motor.
Its efficiency is higher than that of a slip-ring induction motor at all speeds except synchronous speed and is very much high at lower speeds
While operating exactly at synchronous speed it behaves, in a sense. like a synchronous motor with compensating winding functioning as a dc exciter.

⇒ The following motor definitely has a permanent magnet rotor:
DC commutator motor
Brushless dc motor
Stepper motor
Reluctance motor

⇒ If the speed of a dc motor increases with load torque, then it is a
series motor.
permanent magnet.
differentially compounded motor.
cumulatively compounded motor.

⇒ The speed of a universal motor is usually reduced by using
V-belts
gearing.
chains.
brakes.

⇒ Which one of the following statements is not true for anac servomotor?
Has low inertia rotor
Is a single phase motor
Has slip torque characteristic as straight line with negative slope.
Reference voltage frequency is high compared to signal frequency

⇒ Two terminal black box contains one of the R-L-C elements. The black box is connected to a 220 V ac supply. The current through the source is I. When a capacitance of 0.1 F is inserted in series between the source and the box, the current through the source is 2 I. The element is
a resistance.
an inductance.
a capacitance.
it is not possible to determine the element.

⇒ AC series motors in comparison to dc series motors do not have
lesser number of field turns.
larger number of armature conductors.
larger number of poles with lesser flux per pole.
wider air gap.

⇒ Which of the following statements associated with an ae series motor is/are incorrect?
Its speed falls with the increase in load torque.
Its power factor deceases with the increase in load torque.
Its torque-speed characteristic is similar to that of a dc shunt motor.
Its torque-speed characteristic is similar to that of a dc series motor.

⇒ Distortion of the whole core and subsequent damage to the coil insulation dueto intense local eddy currents may be caused clue to failure of
the insulation of the winding.
the insulation between the laminations.
the insulation around the core damping bolts.
both (b) and (c).

⇒ An induction motor with larger number of slots has ____ overload capacity.
low
large
no effect on
none of these

⇒ A 220 V shunt motor develops a torque of 54 Nm at an armature current of 10 A. The torque developed when the armature current is 20 A, is
54 Nm
81 Nm
108 Nm
none of the above.

⇒ If the back emf in a dc motor vanishes suddenly, the motor will
start hunting
burn.
run at very high speed.
run at very slow speed.

⇒ Distributed winding is preferred over concentrated winding as it
reduces noise.
reduces the machine size.
reduces the amount of copper required.
improves the generated emf waveform and adds rigidity and mechanical strength to the winding.

⇒ The speed of a dc motor is
directly proportional to back emf and flux.
directly proportional to its back emf and inversely proportional to flux.
inversely proportional to both hack emf and flux.
directly proportional to flux and inversely proportional to back emf.

⇒ In an induction motor, if the air gap is increased
speed will reduce.
efficiency will improve
power factor will he lowered
breakdown torque will reduce

⇒ In a comparative study of the torque-slip characteristic of a balanced polyphase induction motor and that of a single phase induction motor, it is found that for zero slip
the torque for the former is zero and has a non-zero negative value for the latter.
the torque has a non-zero positive value on the former and has a non-zero negative value on the latter.
the torque is zero on both of the characteristics.
the torque has non-zero positive value on both of the characteristics.

⇒ Rotor resistance speed control used for 3-phase slip-ring induction motors has the drawbacks of
reduced starting torque
lower efficiency and poor speed regulation
both (a) and (b).
none of these

⇒ Which of the following motor is preferred for tape recorder?
Shaded pole motor
Hysteresis motor
Two-value capacitor motor
Universal motor

⇒ The transformer efficiency, under heavy loads, is comparatively low due to
large increase in copper losses in comparison to the output.
large increase in iron losses.
drop in power factor.
none of the above.

⇒ Which of the following statements associated with the installation and preventive maintenance of dc machines is correct?
The commutator should be regularly lubricated in order to reduce brush friction.
Accumulation of dust on the machine may cause electrical failure of the machine.
Perïodic greasing increases the life of the bearings and also provides trouble free service.
None of the above

⇒ In Ward-Leonard system, the lower limit of speed is imposed by
armature resistance.
field resistance.
residual magnetism of the generator.
none of the above.

⇒ Two 10 kV/440 V 1-phase transformers of ratings 600 kVA and 350 kVA are connected in parallel to share a load of 800 kVA. The reactances of the transformers, referred to secondary side are 0.0198 Ω and 0.0304 Ω respectively, (resistance negligible). The load shared by two transformers will be
484.5 kVA and 315.5 kVA.
315.5 kVA and 484.5 kVA.
533 kVA and 267 kVA.
267 kVA and 533 kVA.

⇒ For on-load tap changing the best method is to employ tap-changers
outside the tank operated selector switches.
outside the tank with no selector switch.
inside the tank with no selector switch.
inside the tank operated by external selector switches.

⇒ In a transformer, an insulating material may fail due to
moisture.
dust.
voids in the winding.
any one or more of the above.

⇒ The relationship between rotor frequency f₂, slip s and the stator supply frequency f₁ is given by
f₁ = sf₂
f₂ = sf₁
f₂ =f₁(1 - s)
f₂ = √sf

⇒ Short-circuit test is performed on an induction motor to determine
short-circuit current under rated voltage.
equivalent resistance and reactance.
transformation ratio.
power factor on short-circuit.

⇒ Hydro-generators are generally employed to run at ____ rpm
500
1,000
1,500
3,000

⇒ The most important advantage of using electrical energy in the form of ac is
the construction cost per kW of ac generator is lower than that of dc generator
conductor of smaller x-section is required in case of ac in comparison to dc for carrying the same current.
less insulation is required in case of ac.
transformation of voltage is possible in case of ac only

⇒ For achieving high starting torque and high operation efficiency an induction motor should have ____ rotor circuit resistance at starting and ____ circuit resistance under operating condition.
high, low
low, high
high, high
low, low

⇒ During plugging of an induction motor
phase sequence is reversed.
a dc source is connected to stator.
one phase is open circuited.
power is fed back to mains