Question is ⇒ A class A transformer coupled power amplifier is to deliver 10 W output. The power rating of transistor should not be less than, Options are ⇒ (A) 5 W, (B) 10 W, (C) 20 W, (D) 40 W, (E) , Leave your comments or Download question paper.

Question is ⇒ A class A transformer coupled power amplifier is to deliver 10 W output. The power rating of transistor should not be less than, Options are ⇒ (A) 5 W, (B) 10 W, (C) 20 W, (D) 40 W, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	A class A transformer coupled power amplifier is to deliver 10 W output. The power rating of transistor should not be less than
A.	5 W [Wrong Answer]
B.	10 W [Wrong Answer]
C.	20 W [Correct Answer]
D.	40 W [Wrong Answer]
View Answer 2 -2 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In the transformer shown in the figure, the inductance measured across the terminal 1 and 2 was 4 H with open terminals 3 and 4. It was 3H when the terminals 3 and 4 were short circuited. The coefficient of coupling woul
1
0.707
0.5
indetermine due to insufficient data

⇒

Assertion (A): In 8085, P flag is for parity checking.

Reason (R): If the result of ALU has even parity, P flag is set and if the result has odd parity, P flag is reset.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ The width of air gap on recording head in a tape recorder is about
6 micron
3 micron
1 micron
25 micron

⇒ A BJT is said to be operating in saturation region if
both junctions are reverse biased
both junctions are forward biased
base emitter junction is forward biased and base collector junction is reverse biased
base collector junction is forward biased and base emitter junction is reverse biased

⇒ Voice signal band limited to 3.4 KHz is sampled and pulse code modulated using 64 quantization levels. Ten such signals are time division multiplexed using one 5-bit synchronizing word every alternate frame. The minimum channel bandwidth required for transmission of the TDM signal is
100 KHz
200 KHz
50 KHz
150 KHz

⇒ The most widely used diode rectifier circuit is
half wave
full wave with centre tapped transformer
bridge
either (a) or (b)

⇒ Radio broadcasts are generally
amplitude modulation
frequency modulation
both amplitude and frequency modulation
neither amplitude nor frequency modulation

⇒ In each of circuits below, indicate which diode is conduct
Figure A
Figure B
Figure C
All the three

⇒ The main drawbacks of EEPROM are
low density
high cost
both low density and high cost
none of the above

⇒ In a single phase semi-converter the number of thyristors is
16
8
4
2

⇒ In the given figure reflection coefficient at loa
0.6
-0.6
0.4
-0.4

⇒ For a transfer function the coefficients of the numerator and denominator polynomials in s must be real.
TRUE
FALSE

⇒ When thyristors are connected in parallel, the current distribution may become non-uniform due to
inductive effect of current carrying conductors
capacitive effect of current carrying conductors
both inductive and capacitive effects
none of the above

⇒ In asynchronous TDM, for n signal sources, each frame contains m slots, where m is usually
Less than n
2n
n
greater than 2n

⇒ For a second order system delay time t_d is the time required to reach
half the final value for the very first time
the final value for the very first time
90% of the final value for the very first time
none of the above

⇒ A half bridge inverter
needs a 3 wire dc supply
may use a two wire or 3 wire dc supply
has higher output voltage if fed from 3 wire dc supply
has higher efficiency if fed from 3 wire dc supply

⇒ An ammeter is
secondary instrument
absolute instrument
recording instrument
integrating instrument

⇒ The modulating frequency in frequency modulation is increased from 10 kHz to 30 kHz. The bandwidth is increased by
6
1/6 times
increase by 30 kHz
increase by 20 kHz

⇒ In PAL system
phase of U signal is reversed on alternating lines
phase of V signal is reversed on alternating lines
phases of both U and V signals are reversed on alternating lines
none of the above

⇒ For attenuation of low frequencies we should use
shunt capacitance
series capacitance
shunt inductance
series inductance

⇒ The zinc can of a dry cell serves as positive terminal.
TRUE
FALSE

⇒ The effect of lead resistance is important in measurement of
resistance of shunt
resistance of shunt winding
resistance of ammeter
both (a) and (c)

⇒ Assuming accumulator contain A 64 and the carry is set (1). What will register A and (CY) contain after ACI 0 A4 H?
4 AH, 0
4 AH, 1
4 BH, 0
4 BH, 1

⇒ Which one of the following statement is correct?
Satellite spacing is not affected by the bandwidth of the transmitting earth station
Beamwidth is independent of antenna size and frequency band used
The width of a beam in space is inversely proportional to the width of the transmitting antenna
Use of high-frequency bands permits less number of satellites to share the orbit

⇒ A microprocessor can understand instruction written in
machine language only
mnemonics operation codes only
high language only
both machine language and mnemonics operation codes

⇒ Antenna beamwidth is
measure of directivity
measure of angle
measure of radiation pattern
measure of power pattern

⇒ Consider the following logical IF statement in FORTRAN 77 IF (SALT - PEPPER) 11, 11, 13
IF (SALT - PEPPER) 13, 11, 13
IF (SALT - PEPPER) 13, 11, 11
IF (SALT - PEPPER) 11, 13, 13

⇒ Two voltmeters are each 0-300 V range. Their internal resistances are 10 kΩ and 20 kΩ They are connected is series and a voltage of 400 V is applied. Their readings respectively will be
266.6 and 133.3 V
133.3 and 266.6 V
200 V each
100 and 300 V

⇒ A rectangular waveguide, in dominant TE mode, has dimensions 10 cm x 15 cm. The cut off frequency is
10 GHz
1 GHz
15 GHz
25 GHz

⇒ An ammeter of 0-25 A range has a guaranteed accuracy of 1% of full scale reading. The current measured is 5 A. The limiting error is
0.02
0.025
0.04
0.05