Question is ⇒ A cable carrying alternating current has, Options are ⇒ (A) hysteresis losses only, (B) hysteresis and leakage losses only, (C) hysteresis, leakage and copper losses only, (D) hysteresis, leakage, copper and friction losses, (E) , Leave your comments or Download question paper.

Question is ⇒ A cable carrying alternating current has, Options are ⇒ (A) hysteresis losses only, (B) hysteresis and leakage losses only, (C) hysteresis, leakage and copper losses only, (D) hysteresis, leakage, copper and friction losses, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	A cable carrying alternating current has
A.	hysteresis losses only [Wrong Answer]
B.	hysteresis and leakage losses only [Correct Answer]
C.	hysteresis, leakage and copper losses only [Wrong Answer]
D.	hysteresis, leakage, copper and friction losses [Wrong Answer]
View Answer 28 -27 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The advantage of oil filled cables is
more perfect impregnation
smaller overall size
no ionisation, oxidation and formation of voids
all of the above

⇒ The minimum dielectric stress in a cable is at
armour
bedding
conductor surface
lead sheath

⇒ The electrostatic stress in underground cables is
same at the conductor and the sheath
minimum at the conductor and maximum at the sheath
maximum at the conductor and minimum at the sheath
zero at, the conductor as well as on the sheath

⇒ Conduit pipes are normally used to protect ____ cables.
unsheathed cables
armoured
PVC sheathed cables
all of the above

⇒ In a cable immediately above metallic sheath ____ is provided.
earthing connection
bedding
armouring
none of the above

⇒ The surge resistance of cable is
5 ohms
20 ohms
50 ohms
100 ohms

⇒ In cables the charging current
lags the voltage by 90°
leads the voltage by 90°
lags the voltage by 180°
leads the voltage by 180°

⇒ If the length of a cable is doubled, its capacitance
becomes one-fourth
becomes one-half
becomes double
remains unchanged

⇒ Dielectric strength of rubber is around
5 kV/mm
15 kV/mm
30 kV/mm
200 kV/man

⇒ Cables for 220 kV lines are invariably
mica insulated
paper insulated
compressed oil or compressed gas insulated
rubber insulated

⇒ A certain cable has an insulation of relative permittivity 4. If the insulation is replaced by one of relative permittivity 2, the capacitance of the cable will become
one half
double
four times
none of the above

⇒ In a cable the voltage stress is maximum at
sheath
insulator
surface of the conductor
core of the conductor

⇒ In single core cables armouring is not done to
avoid excessive sheath losses
make it flexible
either of the above
none of the above

⇒ The thickness of the layer of insulation on the conductor, in cables, depends upon
reactive power
power factor
voltage
current carrying capacity

⇒ Solid type cables are considered unreliable beyond 66 kV because
insulation may melt due to higher temperature
of corona loss between conductor and sheath material
there is a danger of breakdown of insulation due to the presence of voids

⇒ The insulating material for a cable should have
low cost
high dielectric strength
high mechanical strength
all of the above

⇒ Cables, generally used beyond 66 kV are
oil filled
S.L. type
belted
armoured

⇒ Copper as conductor for cables is used as
annealed
hardened and tempered
hard drawn
alloy with chromium

⇒ A cable carrying alternating current has
hysteresis losses only
hysteresis and leakage losses only
hysteresis, leakage and copper losses only
hysteresis, leakage, copper and friction losses

⇒ If a cable of homogeneous insulation has a maximum stress of 10 kV/mm, then the dielectric strength of insulation should be
5 kV/mm
10 kV/mm
15 kV/mm
30 kV/mm

⇒ The disadvantage with paper as insulating material is
it is hygroscopic
it has high capacitance
it is an organic material
none of the above

⇒ The bedding on a cable consists of
hessian cloth
jute
any of the above
none of the above

⇒ The insulating material for cables should
be acid proof
be non-inflammable
be non-hygroscopic
have all above properties

⇒ The material for armouring on cable is usually
steel tape
galvanised steel wire
any of the above
none of the above

⇒ In the cables, the location of fault is usually found out by comparing
the resistance of the conductor
the inductance of conductors
the capacitances of insulated conductors
all above parameters

⇒ Low tension cables are generally used upto
200 V
500 V
700 V
1000 V

⇒ Pressure cables are generally not used beyond
11 kV
33 kV
66 kV
132 kV

⇒ The thickness of metallic shielding on cables is usually
0.04 mm
0.2 to 0.4 mm
3 to 5 mm
40 to 60 mm

⇒ The current carrying capacity of cables in D.C. is more than that in A.C. mainly due to
absence of harmonics
non-existence of any stability limit
smaller dielectric loss
absence of ripples

⇒ High tension cables are generally used upto
11 kV
33 kV
66 kV
132 kV