Question is ⇒ A buffer amplifier should have, Options are ⇒ (A) high output impedance and high input impedance, (B) high output impedance and low input impedance, (C) low output impedance an low input impedance, (D) low output impedance and high input impedance, (E) , Leave your comments or Download question paper.

Question is ⇒ A buffer amplifier should have, Options are ⇒ (A) high output impedance and high input impedance, (B) high output impedance and low input impedance, (C) low output impedance an low input impedance, (D) low output impedance and high input impedance, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	A buffer amplifier should have
A.	high output impedance and high input impedance [Wrong Answer]
B.	high output impedance and low input impedance [Wrong Answer]
C.	low output impedance an low input impedance [Wrong Answer]
D.	low output impedance and high input impedance [Correct Answer]
View Answer 2 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The pinch-off voltage is the drain voltage on the shorted gate drain curve above which the drain current becomes
almost negligible
very high
almost constant
highly variable

⇒ A voltage v = 5 + 50 sin ωt/ + 5 sin 5 &omegat is applied to a pure capacitor of capacitance 1 ωF. If f/= 314 rad/sec, current is
1 + 0.0157 cos 314 t + 0.00785 cos 1570 t
0.0157 cos 314 t + 0.00785 cos 1570 t
0.0157 sin 314 t + 0.00785 sin 1570 t
0.0157 sin (314 t / + 45°) + 0.00785 sin (1570 t + 45°)

⇒ The stationary process has
all the statistical Properties dependent on time.
all the statistical Properties independent of time.
aime average is equal to ensemble average.
zero variance.

⇒ The dimensions of EMF are
ML²I^-1T^-3
M^-1T^-3
ML²I^-2T^-3
ML³I^-1T^-3

⇒ In the forward blocking region of a silicon, controlled rectifier, the SCR is
in the off-state
in the ON state
reverse biased
at the point of breakdown

⇒ What is the frequency of audio modulation?
1000 Hz
2000 Hz
3000 Hz
2000 kHz

⇒ Mark out the WRONG statem
Needs very high-speed burst modems
Faces no problems caused by intermodulation of carriers so that transponder can be used at its full power
Needs high-speed manipulation of bit streams
Is less flexible so that channels of widely different capacities cannot used and intermixed

⇒ In the generic microprocessor
instruction cycle time period is shorter than machine cycle time period
machine cycle time period is shorter than instruction cycle time period
instruction cycle time period is exactly half of machine cycle time period
instruction cycle time period is exactly equal to machine cycle time period

⇒ The direction in a Yagi Uda antenna
is longer than the radiating element
is shorter than the radiating element
can be longer or shorter than the radiating element
does not exist

⇒ A transistor has a maximum power dissipation of 350 mW at an ambient temperature of 25°C. If derating factor is 2 mW/°C, the maximum power dissipation for 40°C ambient temperature is
300 mW
330 mW
350 mW
380 mW

⇒ At room temperature the barrier potential in a silicon diode is
0.1 V
0.3 V
0.7 V
1 V

⇒ If the variance σ_x² of d(n) = x(n) - x(n - 1) is one-tenth the variance σ_x² of a stationary zero mean discrete time signal x(n), then the normalized autocorrelation function R_xx(x)/σ_x² at k = 1 is
0.95
0.9
0.1
0.05

⇒ The counter shown in the given figure is built using 4 -ve edge triggered toggle FFs. The FF can be set asynchronously when R = 0. The combinational logic required to realize a modulo-13 counte
F = Q₄ Q₃ Q₂ Q₁
F = Q₄ + Q₃ + Q₂ + Q₁
F = Q₄ + Q₃ + Q₂ + Q₁
F = Q₄Q₃Q₂Q₁

⇒ In a digital measuring device the input electrical signal is in the frequency range of dc to ac (50) Hz. It must be sampled at a rate of
f times/sec
0.5 f times/sec
0.25 f times/sec
2 f times/sec

⇒ A single phase full converter can operate in
4 quadrants
3 quadrants
2 quadrants
1 quadrant

⇒ In figure V_CEQ for each transisto
V_CC
0.5 V_CC
0.75 V_CC
0.25 V_CC

⇒ Brewster angle is the angle for which there is
no reflection and the incident wave is vertically polarized
reflection and the incident wave is horizontally polarized
no reflection and the incident wave is horizontally polarized
none of the above

⇒ The material used in RTD is
linear
aluminium
silver
platinum

⇒ One of the advantages of base modulation over collector modulation of a transistor class C amplifier is
improved efficiency
better linearity
high power output per transistor
the lower modulating power requirement

⇒ High speed logic circuits use
pulses with very small width
pulses with very large width
pulses whose width is neither small nor large
either (b) or (c)

⇒ 'Rotate instruction' in microprocessor belongs to
data transfer group
arithmetic group
logic group
branch group

⇒ The bandwidth required for amplitude modulation is
half the frequency of modulating signal
equal to the frequency of modulating signal
twice the frequency of modulating signal
four times the frequency of modulating signal

⇒ Which of the following is not a proper FORTRAN expression?
B + A / C - D
(A + C) / (B + D)
B + * A / C
A ** (B + 2)

⇒ Wiedemann-Franz law correlates
electrical and thermal conductivities
electron arrangement in shells
temperature and photo electric emission
all of the above

⇒ Thyristors connected in series need :
static equalizing circuit
dynamic equalizing circuit
both static and dynamic equalizing circuits
none of the above

⇒ Out of multiplexer and demultiplexer, which can be used as a logic function generator?
Multiplexer only
Demultiplexer only
Both
None

⇒ Bipolar IC memories are fabricated using
high density versions of the bipolar transistor flip-flop
low density versions of the unipolar transistor flip-flop
high density versions of the MOSFET
low density versions of the MOSFET

⇒ Which characteristics of a memory chip is called dc characteristics?
Organisation
Timing characteristics
Physical dimensions
Power consumption and bus loading

⇒ Which one of the following rules determines the mapping of s-plane to z-plane?
Right half of the s-plane maps into outside of the unit circle in z-plane
Left half of the s-plane maps into outside of the unit circle.
Imaginary axis in s-plane maps in to the circumference of the unit circle.
All of the above

⇒ In 8085 microprocessor, in order to enable INTR interrupt, which of the following instruction are needed?
EI only
SIM only
El and SIM both
None