Question is ⇒ A booser is connected in, Options are ⇒ (A) parallel with earth connection, (B) parallel with the feeder, (C) series with the feeder, (D) series with earth connection, (E) , Leave your comments or Download question paper.

Question is ⇒ A booser is connected in, Options are ⇒ (A) parallel with earth connection, (B) parallel with the feeder, (C) series with the feeder, (D) series with earth connection, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	A booser is connected in
A.	parallel with earth connection [Wrong Answer]
B.	parallel with the feeder [Wrong Answer]
C.	series with the feeder [Correct Answer]
D.	series with earth connection [Wrong Answer]
View Answer 12 -3 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The skin effect of a conductor will reduce as the
resistivity of conductor material increases
permeability of conductor material increases
diameter increases
frequency increases

⇒ The use of strain type insulators is made where the conductors are
dead ended
at intermediate anchor towers
any of the above
none of the above

⇒ The usual spans with R.C.C. poles are
40-50 metres
60-100 metres
80-100 metres
300-500 metres

⇒ Transmission voltage of 11 kV is normally used for distances upto
20-25 km
40-50 km
60-70 km
80-100 km

⇒ If the height of transmission tower is increased, which of the following; parameters is likely to change ?
Capacitance
Inductance
Resistance
All of the above

⇒ The electrostatic stress in underground cables is
zero at the conductor as well as on the sheath
same at the conductor and sheath
minimum at the condactor and minimum at the sheath
maximum at the conductor and minimum at the sheath

⇒ Large industrial consumers are supplied electrical energy at
400 V
11 kV
66 kV
400 kV

⇒ Electro-mechanical voltage regulators are generally used in
reactors
generators
transformers
all of the above

⇒ The spacing between phase conductors of a 220 kV line is approximately equal to
2 m
3.5 m
6 m
8.5 m

⇒ Power system stability is least affected by
reactance of generator
input torque
losses
reactance of transmission line

⇒ Owing to skin effect
current flows through the half cross-section of the conductor
portion of the conductor near the surface carries more current and core of the conductor carries less current
portion of the conductor near the surface carries less current and core of the conductor carries more current
any of the above

⇒ Which of the following can be used for bus-bars ?
Tubes
Rods
Bars
Any of the above

⇒ In aluminium conductors, steel core is provided to
compensate for skin effect
neutralise proximity effect
reduce line inductance
increase the tensile strength

⇒ The operating voltage of extra high tension cables is upto
66 kV
11 kV
33 kV
66 kV

⇒ The top most conductor in a high transmission line is
earth conductor
R-phase conductor
Y-phase conductor
B-phase conductor

⇒ A 3-phase 4 wire system is commonly used on
primary transmission
secondary transmission
primary distribution
secondary distribution

⇒ The effective resistance of a conductor will be the same as 'ohmic resistance' when
power factor is unity
current is uniformly distributed in the conductor cross-section
voltage is low
current is in true sine wave form

⇒ Galvanised steel wire is generally used as
stay wire
earth wire
structural components
all of the above

⇒ In a distribution system major cost is that of
earthing system
distribution transformer
conductors
meters

⇒ Due to which of the following reasons the cables should not, be operated too hot ?
The oil may loose its viscosity and it may start drawing off from higher levels
Expansion of the oil may cause the sheath to burst
Unequal expansion may create voids in the insulation which will lead to ionization
The thermal instability may rise due to the rapid increase of dielectric losses with temperature

⇒ The steel used in steel cored conductors is usually
alloy steel
stainless steel
mild steel
high speed steel

⇒ Which of the following is neglected in the analysis of short transmission lines ?
Series impedance
Shunt admittance
I²R loss
None of the above

⇒ Which of the following has least effect on corona ?
Atmospheric temperature
Number of ions
Size and charge per ion
Mean free path

⇒ For aluminium, as compared to copper, all the following factors have higher values except
specific volume
electrical conductivity
co-efficient of linear expansion
resistance per unit length for same cross-section

⇒ Induction regulators are used for voltage control in
alternators
primary distribution
secondary distribution
none of the above

⇒ The operating voltage of supertension cables is upto
3.3 kV
6.6 kV
11 kV
33 kV

⇒ The voltage drop, for constant voltage transmission is compensated by installing
inductors
capacitors
synchronous motors
all of above

⇒ The power factor of industrial loads is generally
unity
lagging
leading
zero

⇒ For exact compensation of voltage drop in the feeder the booster
must be earthed
must work on line voltage
must work on linear portion of its V-I characteristics
must work on non-linear portion of its V-I characteFistics

⇒ High voltages for transmitting power is economically available from
d.c. currents
a.c. currents
carrier currents
none of the above