Question is ⇒ A beam may be designed as a cased beam if., Options are ⇒ (A) section is of double open channel form with the webs not less than 40 mm apart, (B) overall depth and width of the steel section do not exceed 750 and 450 mm respectively., (C) width of the solid casing is kept at least 100 mm more than the width of the steel flange and having a concrete cover of 50 mm, (D) all the above., (E) , Leave your comments or Download question paper.

Question is ⇒ A beam may be designed as a cased beam if., Options are ⇒ (A) section is of double open channel form with the webs not less than 40 mm apart, (B) overall depth and width of the steel section do not exceed 750 and 450 mm respectively., (C) width of the solid casing is kept at least 100 mm more than the width of the steel flange and having a concrete cover of 50 mm, (D) all the above., (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	A beam may be designed as a cased beam if.
A.	section is of double open channel form with the webs not less than 40 mm apart [Wrong Answer]
B.	overall depth and width of the steel section do not exceed 750 and 450 mm respectively. [Wrong Answer]
C.	width of the solid casing is kept at least 100 mm more than the width of the steel flange and having a concrete cover of 50 mm [Wrong Answer]
D.	all the above. [Correct Answer]
View Answer 24 -12 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The channels get twisted symmetrically with regard to its axis.
parallel to flanges
parallel to web
perpendicular to flanges
perpendicular to web.

⇒ Gantry girders are designed to resist
lateral loads
longitudinal loads and vertical loads
lateral, longitudinal and vertical loads
lateral and longitudinal loads

⇒ Compression force in two end posts The pin of a rocker bearing in a bridge is designed for
bearing and shear
bending and shear
bearing and bending
bearing, shear and bending

⇒ The least dimension in case of a circular column of diameter D is taken as
0.5 D
0.68 D
0.88 D
D

⇒ The maximum axial load which is just sufficient to keep a column in a small deflected shape, is called.
crippling load
buckling load
critical load
all the above.

⇒ The slenderness ratio of a column is zero when its length.
is zero
is equal to its radius of gyration
is supported on all sides throughout its length
is between the points of zero moments.

⇒ If d is the distance between the flange angles,
vertical stiffeners are provided in steel plate girders if the web is less than d/85
vertical stiffeners are provided in high tensile steel plate girders if the web is less than d/175
horizontal stiffeners are provided in steel plate girders if the web is less than d/200
All the above.

⇒ Spans of continuous fillers are considered approximately equal if the longest span does not exceed the shortest span by more than.
5%
10%
15%
20%

⇒

Poisson's ratio for steel within elastic limit, ranges from.

0.15 to 0.20
0.25 to 0.24
0.25 to 0.33
0.33 to 0.35

⇒ The intermediate supports in a bridge are called
Bearing wall
Abutment
Wing wall
Piers

⇒ When the length of a tension member is too long.
a wire rope is used
a rod is used
a bar is used
a single angle is used.

⇒ The effective length of fillet should not be less than
The size of weld
Two times the size of weld
Three times the size of weld
Four times the size of weld

⇒ A simply supported beam carrying a central load, will be safe in deflection if the ratio of its span to depth, is.
< 19
< 24
> 19
> 24

⇒ In case of timber structures, the form factor for solid circular cross-section is taken as
1.18
1.414
1.67
1.81

⇒ The effective length of the intermillet weld, in respect of the thickness of the thinner part joined should not be less than
Two times
Four times
Ten times
Sixteen times

⇒ The percentage of carbon in structural steel is
0.20 to 0.27 %
0.70 to 0.80 %
1.20 to 1.27 %
1.70 to 1.80 %

⇒ According to IRC recommendations the bridge approaches should be straight for a minimum length of
25 m
30 m
50 m
15 m

⇒ The forces acting on the web splice of a plate girder are
axial forces
shear and axial forces
shear and bending forces
axial and bending forces

⇒ A beam is defined as a structural member subjected to.
axial loading
transverse loading
axial and transverse loading
none of these.

⇒ The thickness of the web of a mild steel plate girder is less than d/200. If only one horizontal stiffener is used, it is placed at.
the neutral axis of the section
2/3rd of the depth of the neutral axis from the compression flange
2/5th of the depth of the neutral axis from the compression flange
2/5th of the height of the neutral axis from tension flange

⇒

Web crippling generally occurs at the point where.

bending moment is maximum
shearing force is minimum
concentrated loads act
deflection is maximum

⇒ A piece of round steel forged in place to connect two or more steel members is known as a
Bolt
Rivet
Screw
Nail

⇒ The heaviest I-section for same depth is
ISMB
ISLB
ISHB
ISWB

⇒ Rolled steel angle sections are classified
Equal angles
Unequal angles
Bulb angles
All the above

⇒ Which operation can not be done easily on mild steel ?
Drilling
Punching
Cutting
Hardening

⇒ In the virtual work method, the virtual quantity is
displacement
load
slope
moment

⇒ The strength of a riveted lap joint is equal to its.
shearing strength
bearing strength
tearing strength
least of (a), (b) and (c)

⇒ Which of the following has influence on the strength of timber ?
Moisture content
Presence of defects
Types of grains
All the above

⇒ For a cantilever beam of length L continuous at the support and unrestrained against torsion at the support and free at the end, the effective length l is equal to.
l = L
l = 2L
l = 0.5L
l = 3L

⇒ The effective length of a double angle strut with angles placed back to back and connected to both the sides of a gusset plate, by not less than two rivets, is.
0.5 L
0.67 L
0.85 L
L