Question is ⇒ A (75 - J50) ohm load is connected to a coaxial of Z0 = 75 ohm at 10 GHz. The best method of matching is to connect, Options are ⇒ (A) an inductance at load, (B) a short circuited stub at load, (C) a short circuited stub at specific distance from load, (D) a capacitance at specific distance from load, (E) , Leave your comments or Download question paper.

Question is ⇒ A (75 - J50) ohm load is connected to a coaxial of Z0 = 75 ohm at 10 GHz. The best method of matching is to connect, Options are ⇒ (A) an inductance at load, (B) a short circuited stub at load, (C) a short circuited stub at specific distance from load, (D) a capacitance at specific distance from load, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	A (75 - J50) ohm load is connected to a coaxial of Z₀ = 75 ohm at 10 GHz. The best method of matching is to connect
A.	an inductance at load [Wrong Answer]
B.	a short circuited stub at load [Wrong Answer]
C.	a short circuited stub at specific distance from load [Correct Answer]
D.	a capacitance at specific distance from load [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In the circuit, shown the current I marked is give
2.22 A
1.78 A
4.44 A
0.0833333333333333

⇒ For static electric and magnetic fields in an homogenous source-free medium, which of the following represents the correct form of Maxwell's equations?
Δ.E = 0
Δ.E = 0
Δ x E = 0
Δ x E = 0

⇒ What is the approximate steady state current in the above circ
50 A
25 A
0.208333333333333
0.0416666666666667

⇒

Assertion (A): Many instruments use eddy current damping.

Reason (R): Eddy currents set up a magnetic flux which opposes the original movement which generates them.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒ The maximum power handling capacity of a resistor depends on
total surface area
resistance value
thermal capacity of the resistor
resistivity of the material used in the resistor

⇒ Time delay produced by an instruction code given below using 2 MHz clock
1783 μs
1787 μs
1781 μs
1797 μs

⇒ Which of the following statements is incorrect?
The line integral of B around the circuit is called magnetomotive force
Normal components of B are continuous but the normal components of H are not continuous
Magnetic flux lines are bent away from the normal in the medium with the highest value of permeability
The unit of permeability is henry/metre

⇒ The input to an op-amp integrating amplifier is a constant voltage. The output will be
a constant voltage
a sawtooth wave
a ramp
ac voltage

⇒ If the poles lie in second quadrant, damping ratio is
1
less than 1
zero
more than 1

⇒

Assertion (A): When Diode used as rectifier the reverse breakdown voltage should not be exceeded.

Reason (R): A high inverse voltage can destroy a p-n junction.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ In measurements using strain gauge, the dummy strain gauge is used to
compensate for resistance of strain gauge
compensate for change in temperature
compensate for error due to change in voltage of battery
compensate for error in voltmeter

⇒ In the circuit of figure, the current through battery E_{34 A charging
4 A discharging
4 A charging or discharging depending on value of E₃
4 A charging or discharging depending on values of E₁, E₂, E₃}

⇒

Assertion (A): The expression E = - ΔV, where E is the electric field and V is the potential is not valid for time varying fields.

Reason (R): The curl of a gradient is identically zero.

Both A and R are individually true and R is the correct explanation of A
Both A and R are individually true but R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒ How many roots with positive real parts do the equation s³ + s² - s + 1 = 0 have?
Zero
One
Two
Three

⇒ In figure the voltage drop across diode is 0.7 V. Then the voltage across diode during negative half cycl
10 V
9.3 V
zero
10.7 V

⇒ Due to the formation of Schottky defects the density of the crystal
increases slightly
increases appreciably
decreases slightly
decreases appreciably

⇒ A single phase half wave converter is feeding a resistive load. Output dc power is P_dc and total power delivered to load is P_ac then
P_dc = P_ac for all values of firing angles
P_dc = P_ac if firing angle is less than 180°
P_dc < P_ac for all values of firing angles
P_dc < P_ac if firing angle is less than 180°

⇒ The horizontal intercept of dc load line is the same as ideal
cut off point
saturation point
operating point
quasi saturation point

⇒

Assertion (A): In Hall effect the O.C. transverse voltage developed by a current carrying semiconductor with a steady magnetic field perpendicular to the current direction has opposite signs for n and p semiconductors.

Reason (R): The magnetic field pushes both holes and electrons in the same direction.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ A five bit binary adder is used to add 01001 and 00111. The adders from LSB position are numbered as FA₀, FA₁, FA₂ and FA₃. The outputs of FA₂ are
SUM = 0
SUM = 0, CARRY = 1
SUM = 1, CARRY = 0
SUM = 1, CARRY = 1

⇒ As compared to the number of network elements in Brune synthesis, the number of network elements Bott-and Duffin in realization is
more
less
equal
any of the above

⇒ For a standard 2nd order system the maximum overshoot is 10% to an unit step input. If the magnitude of the input is doubled, then maximum overshoot and percentage of maximum overshoot is:
maximum overshoot doubles and percentage of maximum overshoot is less than double
maximum overshoot doubles and percentage of maximum overshoot do not change
maximum overshoot remain same and percentage of maximum overshoot is double
maximum overshoot more than double and percentage of maximum overshoot is less than double

⇒ Klystron amplifier is not used to amplifier very weak microwave signals due to
low gain for weak signals
low noise for weak signals
high noise
both (a) and (b)

⇒ The following switching functions are to be implemented using a decoder

f₁ = ∑m (1, 2, 4, 8, 10, 14)
f₂ = ∑m (2, 5, 9, 15)
f₃ = ∑m (2, 4, 5, 6, 7)

The minimum configuration of decoder is
2 to 4 line
3 to 8 line
4 to 16 line
5 to 32 line

⇒ A half adder adds __________ bits and a full adder adds __________ bits.
two, three
three, four
four, six
two, four

⇒ Consider the following statements

An assembler is a program having assembly language program as input and machine language program as output.
A macro assembler is an assembler with additional macro facilities.
A cross assembler for a μP X is an assembler which executes on source microcomputer with a different CPU than X bit generates code for X.
Assemblers generally do not provide macro facilities.

Of the above statement
All are correct
only 1, 2, 3 are correct
only 1, 2, 4 are correct
only 1, 3, 4 are correct

⇒ Computer virus is a piece of rough software of unknown origin that
copies itself like a breeding germ
spreads from one machine to another
eats away processing power
all of the above

⇒ Geosynchronous satellites are always launched in the equatorial plane because it is the only plane which provides
24-hour orbit
stationary satellite
global communication
zero-gravity environs

⇒ Ground wave propagation is useful for
microwave
medium wave
short wave
long distance

⇒ A (75 - j 40) W load is connected to a co-axial line of z₀ = 75ω at 6 MHz. The load matching on the line can be accomplished by connecting
a short circuit stub at the load
an inductance at the load
a short circuit stub at a specific distance from the load
a capacitance at a specific distance from the load