Question is ⇒ A 230 V D.C. shlint motor takes 32 A at full load. The back e.m.f. on full load, if the resistance of motor armature and shunt field windings are 0.2 Ω and 115 Ω respectively, will be, Options are ⇒ (A) 210 V, (B) 215 V, (C) 220 V, (D) 224 V, (E) , Leave your comments or Download question paper.

Question is ⇒ A 230 V D.C. shlint motor takes 32 A at full load. The back e.m.f. on full load, if the resistance of motor armature and shunt field windings are 0.2 Ω and 115 Ω respectively, will be, Options are ⇒ (A) 210 V, (B) 215 V, (C) 220 V, (D) 224 V, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	A 230 V D.C. shlint motor takes 32 A at full load. The back e.m.f. on full load, if the resistance of motor armature and shunt field windings are 0.2 Ω and 115 Ω respectively, will be
A.	210 V [Wrong Answer]
B.	215 V [Wrong Answer]
C.	220 V [Wrong Answer]
D.	224 V [Correct Answer]
View Answer 13 -10 Explanation:- Answer : D Discuss it below : Sonu Kumar Said on 2020-12-02 23:23:17 Explanation pls !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ If a D.C. shunt motor is working at no load and if shunt field circuit suddenly opens
nothing will happen to the motor
this will make armature to take heavy current, possibly burning it
this will result in excessive speed, possibly destroying armature due to excessive centrifugal stresses
motor will run at very slow speed

⇒ Which of the following motors one will choose to drive the rotary compressor ?
D.C. shunt motor
D.C. series motor
Universal motor
Synchronous motor

⇒ The speed of a motor falls from 1100 r.p.m. at no-load to 1050 r.p.m. at rated load. The speed regulation of the motor is
0.0236
0.0476
0.0677
0.0884

⇒ In a D.C. generator all of the following could be the effects of iron losses except
Loss of efficiency
Excessive heating of core
Increase in terminal voltage
Rise in temperature of ventilating air

⇒ Which of the following motor has high starting torque ?
Synchronous motor
A.C. series motor
D.C. series motor
Induction motor

⇒ Which D.C. motor Will have least percentage increase of input current for the same percentage increase in the torque?
Shunt motor
Series motor
Cumulative compound motor
Separately excited motor

⇒ The plugging gives the
zero torque braking
smallest torque braking
highest torque braking
none of the above

⇒ According to Fleming's left hand rule, when the forefinger points in the direction of the field or flux, the middle finger will point in the direction of
current, in the conductor
movement of conductor
resultant force on conductor
none of the above

⇒ Which D.C. motor is preferred for elevators ?
Shunt motor
Series motor
Differential compoun.d motor
Cumulative compound motor

⇒ In case the back e.m.f. and the speed of a D.C. motor are doubled, the torque developed by the motor will
remain unchanged
reduce to one-fourth value
increase four folds
be doubled

⇒ Which of the following motors is usually used in house-hold refrigerators ?
D.C. shunt motor
D.C. series motor
Single phase induction motor (split phase start or induction run motor)
Reluctance motor

⇒ What will happen if the back e.m.f. of a D.C. motor vanishes suddenly?
The motor will stop
The motor will continue to run
The armature may burn
The motor will run noisy

⇒ In a manual shunt motor starter
over load relay is connected in series and no volt relay in parallel with the load
over load relay is connected in parallel and no volt relay in series with the load
over load relay and no volt relay are both connected in series with the load
over load relay and no volt relay are both connected in parallel with the load

⇒ As the load is increased the speed of D.C. shunt motor will
reduce slightly
increase slightly
increase proportionately -
remains unchanged

⇒ The speed of a D.C. shunt motor can be increased by
increasing the resistance in armature circuit
increasing the resistance in field circuit
reducing the resistance in the field circuit
reducing the resistance in the armature circuit

⇒ In Ward Leonard method of speed control of a D.C. motor, change in speed of motor is obtained by the
change in armature voltage of D.C. motor
change in the field excitation of the D.C. motor
change in armature current of D.C. motor
change in supply voltage

⇒ As compared to an induction motor, the air gap in a D.C. motor is
less than 50%
between 50% and 90%
same
more

⇒ Which of the following tests can be conducted on all types of D.C. machines ?
Hopkinson's test
Running down test
Block rotor test
Field's test

⇒ A D.C. series motor, as compared to shunt and compound motors, has the highest torque at the start because of its comparatively
stronger series field
lower armature resistance
large armature current
fewer series turns

⇒ In Field's test for series motors one motor drives the other machine as
cumulative compound generator
differential compound generator
separately excited generator
series generator

⇒ Speed control of a cumulatively compounded D.C. motor can be effected through change of
field resistance
armature resistance
armature voltage
any of the above

⇒ The type of D.C. motor used for shears and punches is
shunt motor.
series motor
differential compound D.C. motor
cumulative compound D.C. motor

⇒ VVhat is the effect produced by the electric current in an electric motor ?
Heating effect only
Magnetic effect only
Heating as well as magnetic effect
Heating as well as chemical effect

⇒ Ward-Leonard control is basically a
voltage control method
field divertor method
field control method
armature resistance control method

⇒ If the speed of a D.C. shunt motor is increased, the back e.m.f. of the motor will
increase
decrease
remain same
become zero

⇒ Regenerative braking on shunt motors is used when
the load is variable
the load is constantly decreasing
the load acts as a braking force
the load has overhauling characteristics.

⇒ For which types of D.C. motor, dynamic braking is generally used ?
Shunt motors
Series motors
Compound motors
All of the above

⇒ In case of conductively compensated D.C. series motors, the compensating winding is provided
as separately wound unit
in parallel with armature winding
in series with armature winding
in parallel with field winding

⇒ The simplest form of a motor controller is
relay
toggle switch
drum switch
magnetic switch

⇒ If a D.C. shunt motor is working at full load and if shunt field circuit suddenly opens
this will make armature to take heavy current, possibly burning it
this will result in excessive speed, possibly destroying armature due to excessive centrifugal stresses
nothing will happen to motor
motor will come to stop