Question is ⇒ ____ is preferred for synthetic fibre mills., Options are ⇒ (A) Synchronous motor, (B) Reluctance motor, (C) Series motor, (D) Shunt motor, (E) , Leave your comments or Download question paper.

Question is ⇒ ____ is preferred for synthetic fibre mills., Options are ⇒ (A) Synchronous motor, (B) Reluctance motor, (C) Series motor, (D) Shunt motor, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	____ is preferred for synthetic fibre mills.
A.	Synchronous motor [Wrong Answer]
B.	Reluctance motor [Correct Answer]
C.	Series motor [Wrong Answer]
D.	Shunt motor [Wrong Answer]
View Answer 20 -9 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which of the following motors is preferred for traction work ?
Universal motor
D.C. series motor
Synchronous motor
Three-phase induction motor

⇒ Rotor of a motor is usually supported on____ bearings.
ball or roller
needle
bush
thrust

⇒ While selecting motor for an air conditioner which of the following characteristics is of great importance ?
Type of bearings
Type of enclosure
Noise
Arrangement for power transmission

⇒ Which of the following is essentially needed while selecting a motor ?
Pulley
Starter
Foundation pedal
Bearings

⇒ Which feature, while selecting a,motor for centrifugal pump, will be of least significance ?
Starting characteristics
Operating speed
Horse power
Speed control

⇒ Which of the following motors is usually preferred for kiln drives ?
Cascade controlled A.C. motor
Slip ring induction motor
Three phase shunt wound commutator motor
Any of the above

⇒ The size of an excavator is usually expressed in terms of
crowd' motion
angle of swing
cubic metres
travel in metres

⇒ In ____ the speed can be varied by changing the position of brushes.
slip ring motor
schrage motor
induction motor
repulsion motor

⇒ ____ method of starting a three phase induction motor needs six terminals
Star-delta
Resistance starting
Auto-transformer
None of the above

⇒ For blowers which of the following motors is preferred ?
D.C. series motor
D.C. shunt motor
Squirrel cage induction motor
Wound rotor induction motor

⇒ ____ motor is a constant speed motor.
Synchronous motor
Schrage motor
Induction motor
Universal motor

⇒ For a motor-generator set which of the following motors will be preferred ?
Synchronous motor
Slip ring induction motor,
Pole changing induction motor
Squirrel cage induction motor

⇒ The cost of an induction motor will increase as
horsepower rating increases but r.p.m. decreases
horsepower rating decreases but r.p.m. increases
horsepower rating and operating speed increases
horsepower rating and operating speed decreases

⇒ ____ has least range of speed control.
Slip ring induction motor
Synchronous motor
D.C. shunt motor
Schrage motor

⇒ Which of thefollowing motors is preferred when smooth and precise speed control over a wide range is desired ?
D.C. motor
Squirrel cage induction motor
Wound rotor induction motor
Synchronous motor

⇒ Heat control switches are used in
transformers
cooling ranges
three phase induction motors
single phase

⇒ Which of the following alternatives will be cheaper ?
A 100 H.P. A.C. three phase motor
Four motors of 25 H.P. each
Five motors of 20 H.P. each
Ten motors of 10 H.P. each

⇒ Belted slip ring induction motor is almost invariably used for
water pumps
jaw crushers
centrifugal blowers
none of the above

⇒ When the load is above____ a synchronous motor is found to be more economical.
2 kW
20 kW
50 kW
100 kW

⇒ In jaw crushers a motor has to often start against ____ load.
heavy
medium
normal
low

⇒ The travelling speed of cranes varies from
20 to 30 m/s
10 to 15 m/s
5 to 10 m/s
1 to 2.5 m/s

⇒ The diameter of the rotor shaft for an electric motor depends on which of the following
r.p.m. only
Horse power only
Horse power and r.p.m.
Horse power, r.p.m. and power factor

⇒ A reluctance motor ____
is provided with slip rings
requires starting gear
has high cost
is compact

⇒ ____ is not a part of ball bearing ?
Inner race
Outer race
Cage
Bush

⇒ Which of the following happens when star-delta starter is used ?
Starting voltage is reduced
Starting current is reduced
Both (a) and (b)
None of the above

⇒ A wound rotor induction motor is preferred, as compared to squirrel cage induction motor, when major consideration is
slop speed operation
high starting torque
low windage losses
all of the above

⇒ For a D.C. shunt motor which of the following is incorrect ?
Unsuitable for heavy duty starting
Torque varies as armature current
Torque-armature current is a straight line
Torque is zero for zero armature current

⇒ In case of ____ speed control by injecting e.m.f. in the rotor circuit is possible.
d.c. shunt motor
schrage motor
synchronous motor
slip ring induction motor

⇒ ____ need frequent starting and stopping of electric motors.
Paper mills
Grinding mills
Air-conditioners
Lifts and hoists

⇒ Besides a constant speed a synchronous rotor possesses which of the following advantages ?
Lower cost
Better efficiency
High power factor
All of the above