Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | (1 2 1)_{x} = (1 0 0)_{4} Then x is equal to |

A. | 2 [Wrong Answer] |

B. | 3 [Correct Answer] |

C. | 5 [Wrong Answer] |

D. | does not exist [Wrong Answer] |

View Answer
Explanation:-
Answer : BDiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ The relative permittivity of the ionosphere at ratio frequencies is

> 1

< 1

1

≥ 1

⇒

**Assertion (A):** Tristate logic is used for bus oriented systems

**Reason (R):** The outputs of a tristate logic are 0, 1 and indeterminant.

Both A and R are correct and R is correct explanation of A

Both A and R are correct but R is not correct explanation of A

A is true, R is false

A is false, R is true

⇒ Which of the following statements is incorrect?

A mesh with two resistors has two mesh currents

The algebraic sum of all voltages around any mesh or any loop must be zero

The principle node is a function where branch current can divide or combine

A Norton is a series circuit

⇒ In a CRO, the time base signal is applied to

X plates

Y plates

either X or Y plates

alternately X and Y plates

⇒ A transmission line discontinuity is defined as any interruption in the uniformity of the line.

TRUE

FALSE

⇒ The snubber circuit consists of

a capacitor connected in series with thyristor

a capacitor connected in parallel with thyristor

a resistor and capacitor in series connected across thyristor

none of the above

⇒ A 12 kHz pulse wave-form is amplified by a circuit having an Upper cut-off frequency of 1 MHz. The minimum input pulse width that can be accurately reproduced is

83.33 μ sec

1 μ sec

0.1 m sec

3.5 m sec

⇒ In fabricating silicon BJT in ICs by the epitaxial process, the number of diffusions used is usually

2

3

4

6

⇒ For a full rectified sine wave, the form factor and peak factor respectively are

1.57 and 2

1.57 and 2

1.11 and 1.11

1.11 and 2

⇒ The force required to initiate motion between two contacting surfaces is called

coulomb friction

viscous friction

static friction

none of the above

⇒ Which one of the following is a D to A conversion technique?

Successive approximation

Weighted resistor

Dual slope

Single slope

⇒ For real values of

*x*, the minimum value of the function

*f*(

*x*) exp (

*x*) + exp (-

*x*) is

2

1

0.5

0

⇒ A single phase half wave controlled rectifier circuit has an R-L load. A freewheeling diode is also in the circuit. When freewheeling diode is conducting the SCR

is forward biased

is reverse biased

may be forward biased or reverse biased

forward biased initially but reverse biased afterwards

⇒ When a lead acid cell is in fully charged condition the positive and negative plates are similar.

TRUE

FALSE

⇒ The root locus branches

start from open loop poles and terminate at zeros

start from open loop zeros and terminate at poles

may start from pole or zero and terminate at another pole or zero

none of the above

⇒ A moving iron instrument has

two iron vanes, one fixed and one movable

two movable iron vanes

two aluminium vanes, one fixed and one movable

two vanes, one fixed made of Aluminium and the other movable made of iron

⇒ A network N is dual of network N if

both of them have same mesh equation

both of them have same node equation

mesh equation of one are the node equations of the other

KCL and KVL equations are the same

⇒ A dynamometer wattmeter can be used for

dc only

ac only

dc and 50 Hz ac

dc and high frequency ac

⇒ Is Schottky TTL, Schottky diode is used primary to

prevent saturation of the transistor

saturate the transistor

act as a switch

act as a controlling switch

⇒ Consider the following

- The first letter of a Java variable is lower case.
- Each successive word in Java variable begins with a capital letter.
- All other letters are lower case.
- A Java variable can have a digit as first character.

All

1, 2, 3 only

1, 2, 4 only

2, 3, 4 only

⇒

Match the following:

List I (Laws of Boolean) | List II (Relation algebra) | ||
---|---|---|---|

A. | Distributive law | 1. | x + x = x |

B. | DeMorgans law | 2. | x(y + z) = xy + xz |

C. | Idempotent law | 3. | (x) = x |

D. | Involution law | 4. | (x + y) = xy |

A-1, B-2, C-3, D-4

A-2, B-4, C-1, D-3

A-3, B-4, C-1, D-2

A-4, B-1, C-2, D-3

⇒ In anti-ferromagnetic materials, the graph of susceptibility versus temperature shows a sharp maximum at a certain temperature. This temperature is known as

Curie temperature

Neel temperature

Weiss temperature

Bitter temperature

⇒ In figure, the switch is closed at

*t*= 0 when current through inductor is 6 A, the rate of change of current through resistor is 6 A/s. The value of

1 H

2 H

3 H

4 H

⇒ When performing numerical calculations in floating point arithmetic

- Error may occur due to finite representation of numbers.
- Error may occur due to rounding.
- Error may occur due to finite representation of inherently infinite process.

All

1 and 2 only

1 and 3 only

2 and 3 only

⇒ A circuit which cannot demodulate SSB is

balanced modulator

product detector

BFO

phase discriminator

⇒ A 14 pin AND gate IC has __________ AND gates.

8

6

4

2

⇒ The scale of hot wire instrument is linear.

TRUE

FALSE

⇒ As the temperature of semiconductor is increased

the average number of free charge carriers decreases

the average number of free charge carriers increases

the average number of free charge carriers remains the same

the average number of free charge carriers may increase or decrease

⇒ The function δ (

*t*-

*b*) is a

unit impulse

unit step

unit doublet

none of the above

⇒ The boundary conditions at the interface between two dielectrics in an electric field are given by

D

_{normal}= 0, E

_{tangential}= 0

D

_{normal}= 0, E

_{normal}= 0

D

_{tangential}= 0, E

_{tangential}= 0

D

_{tangential}= 0, E

_{normal}= 0